Use As Directed - SLV Elektronik BRICK MESH LED Instrucciones De Servicio

SLV Elektronik GmbH
ENGLISH
INSTRUCTION MANUAL FOR
RECESSED WALL FITTING
BRICK MESH LED
1. NOTES ON SAFETY
Installation, mounting or works on the electrical connection may
only be carried out by an approved electrician.
Do not cover the product - provide free air circulation!
Do not hang or fasten anything on the product, especially no
decoration.
Keep children away from the product.
The fixture may only be operated with a complete and intact
protection glass.
Do not try to seal the product yourself, using additional silicon or
another sealant.
Operate the product only when it functions properly:
In case of a malfunction you may NOT touch the product or operate it
further. Disconnect the product from the power supply by an external
switch or by the fuse.
If touched or further operated there is danger from electric shock,
burning, or fire.
A malfunction exists when:
visible damages appear.
the product does not work properly (e.g. flickering).
smoke, steam or crackling sounds appear.
smell of burning is recognisable.
an overheating is recognisable (e.g. by discolouration of adjacent
surfaces).
Operate the product only after maintenance and examination by an
approved electrician!
2.

USE AS DIRECTED

This product serves exclusively lighting purposes and may:
only be used with a voltage of 230V ~50Hz.
only be operated when firmly mounted.
not be exposed to strong mechanical loads or to strong
contamination.
only be installed and operated after a condition inspection if the
product is dirty or has been moistened through storage.
not be modified or converted.
3. OPERATION
Replacing the light source: Under regular usage the LED bulb has
an extraordinary long lifetime. If nevertheless damage or failure
occurs, contact your local dealer to exchange the LED bulb.
4. MAINTANANCE AND CARE
The following enviromental influences may have unwanted effects on
the surface of the product:
acid rain and sour soil high salt content in the air
thawing salt cleaning agents
fertilizer especially in flowerbeds
other chemical substances (e.g. herbicides)
Protect the product by adequate means to avoid unwanted changes of the
surface.
Disconnect the product from the power supply and let it cool down,
before you clean the product.
If disregarded there may be danger of electric shock or by burning
when cleaning the product.
Cleaning: Clean the product on a regular basis using a slightly
moistened, soft and fluff-free cloth. Please also note additional supplied
notes on maintanance and care.
5. ADDITIONAL IMPORTANT NOTES
Storage: The product must be stored in a dry and clean environment. Do
not strain the product mechanically during storage.
Warranty: In case of a warranty contact your dealer.
Disposal: Notes on the correct disposal in Germany are found on
www.slv.de.
(only by an approved electrician)
6. INSTALLATION
Switch off the mains or respectively the connection lead before doing
any works.
There exists mortal danger from an electric shock.
Use only parts, which are supplied with the product or are described as
accessories!
Otherwise the product or the whole installation may not be secure.
Danger for life or danger of fire may exist!
Inspect the product for loose parts inside the housing. When there are
loose parts inside the housing and these are not explicitly described the
product may not be installed or operated.
The housing maybe voltage-carrying. Danger of electric shock!
Use the supplied fastening material only when it is suited for the
installation background. If this is not the case use only fastening material
suiting the installation background.
When using fastening material that is not suitable there may be
danger from falling objects.
Unpacking
Carefully take the product out of the packaging removing any transport
safeguards.
Before disposal of the packaging material make sure that all
components of the product are removed.
Installation place
The product is intended for installation in solid walls. It may be installed in
brickwork as well in concrete walls.
Fig. a) Installation in a plastered wall(Recess depth 7cm – thickness of
plaster
Fig. b) Installation in a brick wall.
Fig. c) Installation by casting-in the installation box.
Separate Installation Steps
Remove the front cover and take off the installation box.
Carefully take off the glass.
Unfix the LED board.
------------------------------------------------------------------------------------
Brick wall: Direct the mains lead into the installation box. Insert the
installation box into the recess. Fix it by adequate means (i.e. by
mounting foam)
Concrete wall:
Type 1: Direct the mains lead into the installation box. Fix the
installation box by adequate means on the formwork. Ensure that the
installation box is tight and no liquids get into the installation box
when pouring the wall.
Type 2: Prepare an opening before pouring the wall (using styrofoam
block). Direct the mains lead into the installation box when the wall is
hardened out. Insert the installation box into the opening. Fix it by
adequate means (i.e. by mounting foam).
------------------------------------------------------------------------------------
Direct the mains lead through the gasket into the fixture.
Electrical Connection
The product must be able to be separated by an all pole separation
from the current supply.
Loosen the strain relief. Direct the mains lead through the strain relief.
For electric connection attach the black or brown wire (live conductor)
of the mains lead with the clamp L and the blue wire (neutral
conductor) of the mains lead with the clamp N. The green-yellow wire
(protective conductor) of the mains lead has to be tightly screwed into
the earth clamp of the product.
Insert the fixture into the installation box.
Assemble the fixture in reverse order. Note the proper fit for the gasket.
Tighten the screws in a cross-wise order, to achieve an even pressure
on the gasket.
Check if the product functions properly and is securely fixed.
The product is now ready for operation.
art.-no. 230481/82
01/2009 © SLV Elektronik GmbH, Daimlerstr. 21-23, 52531 Übach-
Palenberg, Germany, Tel. +49 (0)2451 4833-0
Technical Details are subject to change.