Peg-Perego GT3 fortwo Instrucciones De Uso página 18

packing caps from the stroller rods (fig_a) and loosen
the two screws and two caps from the handlebar,
paying attention not to lose them (fig_b). Line the
handlebar up with the two rods by pushing it all the
way in (fig_c). Pay attention to the direction of the
handlebar: place it as shown in the figure to avoid
fitting it the wrong way.
3 Place the cap and the screw (fig_a) and fasten (fig_b)
on both sides of the handlebar.
4 FASTENING THE BRAKE CABLE: to fasten the brake
cable, slip it into the slot as shown in the figure.
5 FENDER: fit the fender into its housing (fig_a) and
tighten the screw (fig_b).
6 MOUNTING THE REAR WHEELS: slip the transparent
plastic over the rear wheels (fig_a) and push them
into the openings on the sides until they click into
place (fig_b).
7 MOUNTING THE FRONT WHEELS: press the button
on the rear ledge (arrow_a) while slipping the front
wheel into place (arrow_b). Pull downward on the
wheels to make sure they are securely fastened.
8 BASKET: fasten the loops of the basket to stroller on the
front (fig_a) and on the side (fig_b). Attach the basket
zipper to the basket rod (fig_c) and then fasten the
elastic to the stroller hooks inside the basket (fig_d).
9 REAR SEAT: place the rear seat inside the basket (fig_
a), slip the string into the loop (fig_b) and fasten it to
the hook under the rear ledge (fig_c). Finally fasten
the basket zipper to the seat (fig_d).
10 HOOD: to fit the hood, insert the side fasteners into
the special housings (fig_a), button the hood to the
back of the backrest (fig_b) and to the inside of the
armrests (fig_c).
11 Lower the braces to stretch the hood (fig_a).
When you lift the movable part of the hood, you will find
a net insert that provides better ventilation to the baby
(fig_b). To remove the hood, fold the braces, unbutton the
hood, press the side button (fig_c) while slipping the hood
fastener out of its housing (repeat on the other side).
12 COVER: zip the cover to the footrest (fig_a), fasten it
to the side by the Velcro (fig_b) and secure it with the
button (fig_c).
13 5-POINT SAFETY HARNESS: to attach the safety harness,
insert the two buckles of the waist strap (with shoulder
straps attached – arrow_a) into the leg divider strap
until they click into place (arrow_b). To release, push the
round button placed in center of the buckle upwards
(arrow_c) and pull the waist strap outwards (arrow_d).
14 To tighten the waist strap, pull on both sides in the
direction of the arrow (arrow_a). To loosen it, do the
opposite. The waist strap can be tightened as far as
the safety lock (fig_b).
15 To adjust the height of the safety harnesses, release
two the buckles on the rear of the backrest; pull
the shoulder straps towards you (arrow_a) until the
buckles are released and insert them in the backrest
loops (arrow_b). Remove the shoulder straps from
the sack (arrow_c) and insert them in the most
appropriate loop (arrow_d), then re-attach the two
buckles on the rear of the backrest (arrow_e).
16 BRAKE: to brake the stroller, pull the handle on the
handlebar towards you (arrow_a); to release the brake,
disengage the lever (arrow_b). Always set the brake
when the stroller is not moving. To adjust the brake and
tighten it, unscrew the adjuster (fig_c) on the handlebar
to the outside. To loosen the brake, do the opposite.
17 ADJUSTABLE HANDLEBAR: the handlebar on the
stroller is height-adjustable. To adjust the height of the
handlebar, simultaneously press the side buttons (fig_a)
and block the handlebar in the desired position (fig_b).
18 ADJUSTING THE BACKREST: the backrest of the stroller
can be reclined to several positions. To lower the
backrest, lift the handle (arrow_a) as you recline the
backrest (arrow_b), locking it at the desired position.
To raise it, push the backrest up.
19 ADJUSTING THE FOOTREST: the footrest can be
adjusted to two positions. To lower the footrest,
pull the two side levers downwards (fig_a) while
lowering the footrest (fig_b). To raise the footrest, lift
it upwards until it clicks into place.
20 FRONT BAR: the practical front bar opens and closes
to make it easier for the child to get in and out of the
stroller when he/she is older.
To open the front bar, press the button located under
the armrest (arrow_a) and pull the front bar outwards
at the same time (arrow_b). To close the front bar, do
the opposite. The front bar can be removed. The front
bar is also extendible – to extend the front bar, press
the long button located under the armrest (arrow_c)
and pull the front bar outwards (arrow_d). To shorten
the front bar, press the long button and push the
front bar into the armrest.
21 SIDE CUP HOLDERS: the stroller is equipped with
two side cup holders that fold away or pull out as
necessary. To pull the cup holder out, turn the upper
part upwards (arrow_a) and lower the bottom part
(arrow_b). Turn the disk outwards (arrow_c) and
place your drink in the holder (fig_d) To close the cup
holder, do the opposite.
22 RAIN CANOPY: fit the rain canopy onto the stroller
and button it on the side to the hood (fig_a), button
the two sides of the rain canopy elastic to the bottom
of the front frames (fig_b).
23 The practical rain canopy can be lowered and remains
attached to the stroller through the buttons.
24 POUCH: place the pouch near its own housings,
located on the handlebar, and fasten it (fig_a). The
pouch can be worn as an accessory using the special
belt (fig_b).
25 SWIVELING OR STATIONARY FRONT WHEEL: to set the
front wheel on stationary, turn the knob to the closed
padlock (fig_a). To swivel the front wheel, turn to the
open padlock (fig_b).
26 AIR PUMP: to inflate the tires, use the pump located
under the seat (fig_a). Slip the hose off the pump
(fig_b) and screw it onto the opposite end of the
pump (fig_c). Remove the cap from the tire (fig_d)
and fasten the end of the pump hose (fig_e).
_ Before using the stroller for the first time, you are advised
to inflate the tires to a pressure of 25 P.S.I./1.7 bar.
27 SHOCK ABSORBERS: all the wheels are equipped with
shock absorbers. The rear wheels have adjustable
shock absorbers. You can choose from "HARD" for
soft terrain, such as sand and lawns, "SOFT" for rough
surfaces, such as gravel and cobble stones, and
"MEDIUM" for smooth, firm surfaces. To adjust the
shocks on the rear wheels, turn the knob to choose
one of the three settings. It is recommended to adjust
both rear wheels to the same setting.
28 REMOVING THE WHEELS: to remove the rear wheels
press the button (arrow_a) and pull the wheels off
the sides of the stroller (arrow_b). To remove the front
wheel, press the button on the rear ledge (arrow_c)
and pull the wheel off (arrow_d).
29 FOLDING UP: before folding up the stroller, set the
front wheels to stationary. If the hood is mounted,
loosen the braces. To fold the stroller up, press button
number 1 (fig_a) using your right hand. Using your
left hand, grab the handle, press button number 2
(fig_b) and lift up the handle (fig_c). To complete the
folding, turn and fasten the safety hook (fig_d).
30 REMOVABLE FRONT SEAT LINING: unbutton the sack
from the seat (fig_a) and slip the sack off the footrest
(fig_b). Detach the sack from the armrests (fig_c).
31 Pull the leg divider strap up from under the seat (fig_a),
unbutton the side tabs from the backrest (fig_b) and slip
the tabs off the backrest (fig_c). Then remove the sack.
32 REMOVABLE REAR SEAT LINING: unbutton the sack
- 18 -