Technical Data; Before Using The Equipment - Toolson PRO-ABH 2000 Manual De Instrucciones

4. Technical data

Motor power supply: ............................... 20 V DC
Idling speed: .....................................0-1400 min
Clockwise/counter-clockwise: ........................Yes
Blow rate: ........................................ 0-4550 min
Blow strength: .................................................2 J
Drilling capacity concrete/stone (max.): ... 18 mm
Battery charger input voltage: .............................
............................................. 230-240V~ 50/60Hz
Battery charger output voltage: ................ 21.5 V
Battery charger output current: .................... 3.5 A
Charging time: ............................................. 1.5 h
Battery type: ............................................... Li-Ion
Battery capacitance: .................................... 4 Ah
Weight ........................................................2.2 kg
Danger!
Sound and vibration
Sound and vibration values were measured in
accordance with EN 60745.
L sound pressure level ..................... 85,6 dB(A)
pA
K uncertainty ............................................. 3 dB
pA
L sound power level ....................... 96,6 dB(A)
WA
K uncertainty ............................................. 3 dB
WA
Wear ear-muff s.
The impact of noise can cause damage to hea-
ring.
Total vibration values (vector sum of three direc-
tions) determined in accordance with EN 60745.
Impact drilling in concrete
Vibration emission value a
K uncertainty = 1.5 m/s
The specifi ed vibration value was established in
accordance with a standardized testing method. It
may change according to how the electric equip-
ment is used and may exceed the specifi ed value
in exceptional circumstances.
The specifi ed vibration value can be used to
compare the equipment with other electric power
tools.
The specifi ed vibration value can be used for initi-
al assessment of a harmful eff ect.
Anl_PRO_ABH_2000_SPK7.indb 19 Anl_PRO_ABH_2000_SPK7.indb 19
-1
-1
= 5,077 m/s
2
h
2
- 19 -
GB
Keep the noise emissions and vibrations to a
minimum.
•
Only use appliances which are in perfect wor-
king order.
•
Service and clean the appliance regularly.
•
Adapt your working style to suit the appliance.
•
Do not overload the appliance.
•
Have the appliance serviced whenever ne-
cessary.
•
Switch the appliance off when it is not in use.
•
Wear protective gloves.
Caution!
Residual risks
Even if you use this electric power tool in
accordance with instructions, certain resi-
dual risks cannot be rules out. The following
hazards may arise in connection with the
equipment's construction and layout:
1. Lung damage if no suitable protective dust
mask is used.
2. Damage to hearing if no suitable ear protec-
tion is used.
3. Health damage caused by hand-arm
vibrations if the equipment is used over a
prolonged period or is not properly guided
and maintained.
Limit the operating time.
All stages of the operating cycle must be
considered (for example, times in which the
electric tools are switched off and times in which
the tool is switched on but operates without load).

5. Before using the equipment

Be sure to read the following information before
you put the cordless impact drill into operation:
1. Charge the battery pack only with the charger
supplied.
2. Only ever use sharp drill bits and screwdriver
bits which are suitable for the purpose and in
faultless condition.
3. Using a cable/pipe detector, check the area
you want to work on for concealed electric
cables and gas and water pipes.
5.1 Additional handle (Fig. 2/Item 10)
For safety reasons you must only use the
impact drill with the additional handle.
The additional handle (10) enables you to achieve
better stability whilst using the impact drill. For
safety reasons the machine must not be used
23.05.2018 14:12:41 23.05.2018 14:12:41