ALPHA-TOOLS A-FS 1800 UG Manual De Instrucciones página 14

Anleitung_A_FS_1800_UG_SPK7:_
GB
7. RCD plug (Fig. 21)
Connect the RCD plug (41) to the power supply.
Press the reset button (42) and the control lamp (43)
will begin to shine. Press the test button (44) to
check the function of the RCD plug. If everything is
working properly the control lamp (43) will go out and
the contact to the power supply will be interrupted.
The RCD plug triggers at a fault current of 30 mA.
Defective RCD plugs must be replaced by a qualified
electrician.
Press the reset key (42) again in order to be able to
start up the machine.
8. Assembly and operation (Fig. 3-13)
8.1 Assembling the base frame (Fig. 4-8)
Fasten the 4 feet (1) to the base frame (18) as
shown in Figure 5/6. Then fit the two trough mounts
(f) as shown in Figure 7. Insert the trough (3) in the
base frame and fix it in place by tightening the star
grip screws (d).
8.2 Assembling the star handle screws (Figure 9)
Fit the star handle screws (d) as shown in Figure 9.
8.3 Assembling the cooling water pump
(Fig. 10-11)
Place the cooling water pump (13) in the water
trough as shown in Figure 10 and secure it to the
base of the trough with the suction cups. The
pump, cable and cooling water hose (14) must
not be able to get into the cutting area.
Fill with water until the pump (13) is completely
immersed in water.
8.4 Transport brace (Fig. 12-13)
Remove the star handle screw (11) and spacer (40).
Important: Before you lift the equipment out of the
trough or transport it, the cutting unit must be
secured again with the star handle screw (11) and
spacer (40).
8.5 ON/OFF switch (Fig. 2)
To switch on, press the "1" on the ON/OFF
switch (16).
Before you begin cutting, wait until the cutting
wheel has reached maximum speed and the
cooling water pump (13) has started supplying
the cutting wheel with water.
To switch off, press the "0" on the switch (16).
14
05.08.2009 9:58 Uhr Seite 14
8.6 90° Cutting (Fig. 14-15)
Undo the screws (28) and push the angle stop
(5) into the required position.
Loosen the star grip screw (27).
Set the angle stop (5) to 90° and retighten the
star grip screw (27).
Retighten the screws (28) to fasten the angle
stop (5).
Move the machine head (29) to the far end with
the handle (9).
Position the tile against the rail fence (6) on the
angle stop (5).
Switch on the tile cutting machine.
Caution: Always wait until the cooling water has
reached the cutting wheel (2) first.
Move the machine head (29) slowly and
smoothly forward through the tile with the handle
(9).
Switch off the tile cutting machine after
completion of cutting.
8.7 45° Diagonal cut (Fig. 14, 16)
Set the angle stop (5) to 45°.
Cut as described in 8.6
8.8 45° Lengthwise cut, "jolly cut" (Fig. 17-18)
Loosen the star grip screw (10).
Tilt the guide rail (7) to the left to 45° on the
angle scale (17).
Retighten the star grip screw (10).
Cut as described in 8.6.
8.9 Changing the diamond cutting wheel
(Fig. 19-20)
Pull out the power plug.
Unscrew the 3 screws (30) and remove the
safety hood (8) for the blade.
Place the wrench (31) on the motor shaft and
hold.
Using the wrench (34), loosen the flange nut in
the direction of rotation of the cutting wheel (2).
(Caution: Left-hand screw-thread.)
Remove the outer flange (35) and cutting wheel
(2).
Clean the mounting flange thoroughly before
fitting the new cutting wheel.
Fit the new cutting wheel by following the above
procedures in reverse and then tighten.
Caution: Pay attention to the direction of rotation
of the cutting wheel!
Mount the safety hood (8) for the blade again.