Hander HBS-730 Instrucciones De Servicio página 2

5
1
2
4
1 3
5
2
1
2 3
6
max 60-80%
100%
English tool (tools with a rating of 230V or 240V can also be
English
● Do not continue to use worn, torn or heavily clogged
connected to a 220V supply)
sanding belts
● If the drill bit becomes unexpectedly jammed
● Wear protective gloves, safety glasses, close-fi tting
(causing a sudden, dangerous reaction),
Hammer drill clothes and hair protection (for long hair)
Belt sander
immediately switch off the tool
● Always disconnect plug from power source before
making any adjustment or changing any accessory ● Be aware of the forces that occur as a result of
INTENDED USE
INTENDED USE jamming (especially when drilling metals); always
WHEN CONNECTING NEW 3-PIN PLUG (U.K.
This tool is intended for dry sanding with high removal This tool is intended for hammer drilling in brick,
ONLY): hold the tool firmly with both hands and take a
concrete and stone as well as for drilling in wood,
performance of wood, plastic, metal, etc. ● Do not connect the blue (= neutral) or brown (= live) secure stance
metal, ceramic and plastic. Tools with electronic
wire in the cord of this tool to the earth terminal of the ● Always disconnect plug from power source before
TECHNICAL SPECIFICATIONS speed control and left/right rotation are also suitable 1
plug making any adjustment or changing any accessory
for screwdriving and thread cutting ● If for any reason the old plug is cut off the cord of
● Holding the tool
this tool, it must be disposed of safely and not left unat-
PRODUCT ELEMENTS 2 - keep the ventilation slots uncovered
TECHNICAL SPECIFICATIONS 1 tended
- do not apply too much pressure on the tool; let the
● before the sanding surface reaches the workpiece,
1 On/off switch tool do the work for you
you should switch on the tool
2 Knob for locking on/off switch
PRODUCT ELEMENTS 2
● before switching off the tool, you should lift it from
3 Lever for changing sanding belt Your machine is double insulated in
the workpiece
4 Arrow
accordance with EN 50144; therefore
1 On/Off switch with speed control
5 Knob for adjusting belt centering
no earthwire is required.
2 Switch locking button
Your machine is double insulated in accord-
6 Dustbag
3 Wheel for maximum speed control
ance with EN 50144; therefore no earthwire is
SAFETY
MAINTENANCE
4 Switch for changing direction of rotation required.
WARNING! Read all instructions. Failure to follow all in-
5 Switch for selecting drilling function
structions listed below may result in electric shock, fi re
Make sure that the machine is not live
6 Auxiliary handle MAINTENANCE
and/or serious injury.
when carrying out maintenance work
on the motor.
SAFETY Make sure that the machine is not live when
● Avoid damage that can be caused by screws, nails
WARNING! Read all instructions. Failure to follow
and other elements in your workpiece; remove them carrying out maintenance work on the motor.
Regularly clean the machine housing with a soft
all instructions listed below may result in electric
before you start working
cloth, preferably after each use. Keep the
shock, fire and/or serious injury. Regularly clean the machine housing with a soft cloth,
● Always keep the cord away from moving parts of the
ventilation slots free from dust and dirt.If the dirt
tool; direct the cord to the rear away from the tool preferably after each use. Keep the ventilation slots free
does not come off use a soft cloth moistened with
● When you put away the tool, switch off the motor and ● Wear ear protectors with hammer drills (exposure from dust and dirt.If the dirt does not come off use a soft
cloth moistened with soapy water. Never use solvents soapy water. Never use solvents such as petrol,
ensure that all moving parts have come to a complete to noise can cause hearing loss)
such as petrol, alcohol, ammonia water, etc. These sol- alcohol, ammonia water, etc. These solvents may
standstill ● Use auxiliary handles supplied with the tool (loss
● Use completely unrolled and safe extension cords vents may damage the plastic parts. damage the plastic parts.
of control can cause personal injury)
The machine requires no additional lubrication.
with a capacity of 16Amps (U.K. 13 Amps) ● Avoid damage that can be caused by screws, The machine requires no additional lubrication.
Should a fault occur, e.g. after wear of a part, please
● In case of electrical or mechanical malfunction, imme- Should a fault occur, e.g. after wear of a part,
nails and other elements in your workpiece; remove
diately switch off the tool and disconnect the plug contact your local SBM Group dealer.
them before you start working please contact your local SBM Group dealer.
● SBM GROUP can assure fl awless functioning of the
● Always keep the cord away from moving parts of
ENVIRONMENT
tool only when original accessories are used
the tool ENVIRONMENT
● This tool should not be used by people under the age In order to prevent the machine from damage during
In order to prevent the machine from damage
● When you put away the tool, switch off the motor
of 16 years transport, it is delivered in a sturdy packaging. Most of
and ensure that all moving parts have come to a during transport, it is delivered in a sturdy
● The noise level when working can exceed 85 dB(A); the packaging materials can be recycled. Take these
packaging. Most of the packaging materials can be
complete standstill
wear ear protection materials to the appropriate recycling locations. Take
● Use completely unrolled and safe extension cords recycled. Take these materials to the appropriate
● If the cord is damaged or cut through while working, your unwanted machines to your local SBM Group
recycling locations. Take your unwanted machines
with a capacity of 16 Amps (UK 13 Amps)
do not touch the cord, but immediately disconnect the dealer. Here they will be disposed of in an environmen-
● In case of electrical or mechanical malfunction, to your local SBM Group dealer. Here they will be
plug tally safe way.
disposed of in an environmentally safe way.
immediately switch off the tool and disconnect the
● Never use tool when cord is damaged; have it re-
plug
placed by a qualifi ed person
● SBM Group can assure flawless functioning of
● Always check that the supply voltage is the same as
the tool only when original accessories are used
the voltage indicated on the nameplate of the tool (tools
with a rating of 230V or 240V can also be connected to ● Use only accessories with an allowable speed
matching at least the highest no-load speed of the
a 220V supply)
● This tool is not suitable for wet sanding tool
● Do not work materials containing asbestos (as- ● This tool should not be used by people under the
bestos is considered carcinogenic) age of 16 years
● Take protective measures when during work dust ● Be careful not to drill or drive into areas where
can develop that is harmful to one's health, com-
electrical wires may be contacted
bustible or explosive (some dusts are considered car-
● If the cord is damaged or cut through while
cinogenic); wear a dust mask and work with dust/chip
working, do not touch the cord, but immediately
extraction when connectable
disconnect the plug
● When sanding metal, sparks are generated; do not
● Never use tool when cord is damaged; have it
use dustbox/dustbag/vacuum cleaner and keep other
replaced by a qualified person
persons and combustible material from work area
● Always check that the supply voltage is the same
● Do not touch the running sanding belt
as the voltage indicated on the nameplate of the
6