Technical Specification - Sundstrom SR561 Instrucciones De Uso

Taking the equipment off
See also the user instructions for fan unit SR 500/SR 500 EX/
SR 700 or compressed air attachment SR 507 whichever is used.
• Slacken the face seal (short hood SR 562) or the neck band
(long hood SR 561). In emergency situations, the hood can be
taken off with the rubber band tightened.
After use, the equipment must be cleaned and inspected.
See 5. below.

4. Technical specification

Classification according to ATEX-directive 94/9/EC and
IECEx scheme.
See under par.7, Approvals.
Shelf life
The equipment has a shelf life of 5 years from the date of manufacture.
Materials
• Hood: Tyvek 1443R, 200 µm
• Neck seal of SR 561: Cotton/modal/lycra
• Face seal of SR 562: Polyamide/lycra
• Breathing hose: Polyurethane (PU)
• Visor: 0.5 mm PETG
Temperature range
• Storage temperature: from -20 to +40 °C at a relative humidity
below 90 %.
• Service temperature: from -10 to +55 °C at a relative humidity
below 90 %.
Service temperature when used together with fan SR 500 EX is
-10 to +40 °C.
Weights
SR 561: Approx. 450 g, including hose.
SR 562: Approx. 420 g, including hose.
5. Maintenance
The person who is responsible for cleaning and maintenance of
the equipment must have received suitable training and be well
acquainted with work of this type.
Cleaning
Sundström cleaning tissues SR 5226 are recommended for daily
care.
If the equipment is more heavily soiled, use a soft brush or sponge
moistened with a solution of water and dishwashing detergent or
the like. Rinse the equipment and leave it to dry.
N.B. Never use a solvent for cleaning.
Storage
After cleaning, store the equipment in a clean and dry place at
room temperature. Avoid exposing it to direct sunlight or other
heat sources.
Maintenance schedule
The schedule below represents the minimum requirements for
maintenance routines in order to ensure that the equipment will
always be in functional condition.
Visual inspection
Performance check
Cleaning
Before use After use
• •
•
•
Spare parts
Always use genuine Sundström parts. Do not modify the equipment.
The use of non-genuine parts or modification of the equipment
may reduce the protective function and put at risk the approvals
granted to the product.
To change the sweat band
The sweat band is secured with Velcro tape to the forehead band.
Proceed as follows:
• Pull the sweat band off.
• Fit the Velcro tape with the rough side towards the forehead
band and the notch at the top.
To change the long SR 561 Tyvec hood
• Release the hose from the adapter.
• Release the three press-studs at the top edge of the visor.
• Turn the hood inside out.
• Release the press stud from the hose attachment and pull the
hood off the head harness. Fig. 9.
• Place the new hood in front of you, with the visor facing up.
• Attach the press stud to the hose attachment and pull the hood
over the head harness.
• Fix the head harness with the three press studs onto the upper
edge of the visor. Start with the middle one.
• Mount the hose in the adapter.
• Check that the head harness is straight in the hood and that the
hose passage of the hood is not twisted around the hose.
To change the short SR 562 Tyvec hood
• Release the hose from the adapter.
• Release the face seal rubber bands secured to the forehead
band next to the Velcro tapes. Fig. 10.
• Remove the Velcro tapes.
• Release the three press-studs at the top edge of the visor.
• Lift the head harness out of the hood.
• Place the new hood in front of you, with the visor facing down-
wards.
• Grip the front part of the head harness with one hand and insert
it into the hood. Fig 11.
• Make sure that the Velcro tape is stretched under the forehead
band of the head harness (Fig. 12) and secure the hood by
means of the three press-studs at the top edge of the visor.
• Fold the Velcro tapes around the forehand band and secure
them as firmly as possible.
• Take the face seal rubber band and insert the knot into the
keyhole opening in the head harness. Secure it by pulling the
rubber band into the narrow part of the slot. Fig. 13.
• Mount the hose in the adapter.
• Check that the head harness is straight in the hood and that the
hose passage of the hood is not twisted around the hose.
Replace the hose, SR 561/SR 562.
• Fold the hood fabric up at the hose attachment. Fig. 14.
• Twist the hose and pull it out of the adapter. Fig 15.
• Fit the new hose into the head harness in the reverse order.
One hose connection is fitted with an O-ring. Fig. 3. This end
should be connected to the fan/compressed air unit. Fig. 4.
To change the head harness
Follow the relevant parts of the above instructions dealing with
changing the hood.
19