Peg-Perego UNO Instrucciones De Uso página 14

EN_English
Thank you for choosing a Peg-Pérego
product.
WARNING
_ IMPORTANT: READ THESE
INSTRUCTIONS CAREFULLY
AND KEEP THEM FOR FUTURE
REFERENCE. FAILURE TO FOLLOW
THESE INSTRUCTIONS COULD PUT
THE CHILD'S SAFETY AT RISK.
_ THIS PRODUCT IS DESIGNED FOR A
CHILD WHOSE MAXIMUM WEIGHT
IS 45 POUNDS (20 KG) AND WHOSE
MAXIMUM HEIGHT IS 43 INCHES
(110 CM). THIS SHOPPER BASKET IS
DESIGNED TO CARRY A MAXIMUM
WEIGHT OF 11 POUNDS (5 KG). ANY
CUPHOLDER EVENTUALLY PROVIDED
WITH THIS UNIT IS DESIGNED
TO CARRY A MAXIMUM WEIGHT
SPECIFIED ON THE CUPHOLDER
ITSELF. ANY POACH OR POCKET
PROVIDED WITH THIS UNIT IS
DESIGNED TO CARRY A MAXIMUM
WEIGHT OF 0.44 POUNDS (0.2 KG).
_ FAILURE TO FOLLOW
MANUFACTURER'S SPECIFICATIONS
OR USE OF ACCESSORIES OTHER
THAN THOSE APPROVED BY THE
MANUFACTURER MAY CAUSE THE
UNIT TO BECOME UNSTABLE.
_ AVOID SERIOUS INJURY FROM
FALLING OR SLIDING OUT. ALWAYS
USE COMPLETE 5 POINT SEAT BELT.
_ NEVER LEAVE YOUR CHILD
UNATTENDED.
_ ALWAYS USE ALL THE BRAKES
WHENEVER PARKED.
_ TO AVOID SERIOUS INJURY, WHEN
MAKING ADJUSTMENTS ENSURE
THE CHILD'S BODY IS CLEAR OF ALL
MOVING PARTS.
_ ALL OPERATING AND ASSEMBLY
PROCEDURES SHOULD BE
PERFORMED BY AN ADULT.
_ DO NOT LIFT THE STROLLER BY
GRIPPING THE FRONT BAR. THE
FRONT BAR IS NOT DESIGNED TO
WITHSTAND LOADS.
_ ENSURE THAT THE STROLLER IS
OPENED CORRECTLY AND LOCKED IN
POSITION OF USE.
_ CHECK TO MAKE SURE THAT THE
CAR SEAT OR THE BABY CARRIAGE
IS CORRECTLY FASTENED TO THE
STROLLER (WHERE APPLICABLE).
_ DO NOT DRIVE THIS PRODUCT
AROUND STAIRS OR STEPS; CARE
MUST BE TAKEN IF UNIT IS USED ON
STAIRS OR ESCALATORS.
_ DO NOT USE THE PRODUCT IF IT HAS
BROKEN OR MISSING PARTS.
_ DO NOT USE NEAR FIRE OR EXPOSED
FLAME.
_ CHILD MAY SLIP INTO LEG OPENINGS
AND STRANGLE, NEVER USE IN RECLINE
CARRIAGE POSITION UNLESS FOOTREST
ENCLOSURE IS FULLY INSTALLED/
IMPLEMENTED (SEE MANUAL
INSTRUCTIONS FOR CORRECT USE).
NOTICE:
_ THIS ARTICLE MEETS OR EXCEEDS
ALL REQUIREMENTS COVERED IN
ASTM F833 STANDARD AND LATEST
REVISIONS.
INSTRUCTIONS
1 OPENING: press both buttons on the
handlebar at the same time and lock it in the
vertical position (fig_a). Release the two clips
(fig_b), pull the handle up firmly (fig_c) then
push it down until it locks into position.
2 FITTING THE HANDLE: Use a screwdriver to
remove the two screws, taking care not to
lose them (fig_a). Remove the caps on the
ends of the handle and slot it into the tubes
(fig_b). Check the position with the figure to
ensure it is not on backwards. Fully tighten
the screws on both sides of the handle (fig_
c), but do not force them.
3 FITTING THE WHEELS: Place the large wheels
alongside their slots and push them in until
they click into place.
4 BASKET: to fit the basket, press the side buttons
(fig_a) and pull out the basket ring (fig_b).
Check that it is correctly positioned (fig_c).
5 Slide the ring into the basket fabric (fig_a)
and push it into the housing on the stroller
until it clicks into position. Clip the basket
onto the buttons on the side (fig_b) and slip
the two loops onto the stroller at the front.
(fig_c).
- 14 -