Keyboard Input - Onkyo HT-R997 Manual De Instrucciones

> Before Start > Part Names
measurement, so be careful of your surroundings. Keep the
room as quiet as possible during measurement.
0 If you have connected a subwoofer, check the power and
volume of the subwoofer. Set the subwoofer volume to
more than halfway.
0 If the power of this unit suddenly turns off, the wires in
the speaker cables may have touch the rear panel or
other wires and tripped the protection circuit. Twist the
wires again properly and make sure they do not stick out
of the speaker terminals when connecting.
0 After completing Initial Setup, you can also manually
adjust the settings for each speaker to suit the specific
characteristics of each room.
1. Place the supplied speaker setup microphone in the listening
position, and connect to the SETUP MIC jack on the main unit.
SETUP MIC
When putting the speaker setup microphone on a tripod,
refer to the illustration when putting it in place.
2. Select the connected speaker configuration.
AccuEQ Room Calibration
Speaker Channels 7.1 ch < >
Subwoofer Yes
Height Speaker ---
Zone Speaker No
Bi-Amp No
Select how many speakers you have.
16
> Install > Initial Setup
The image on the screen changes as you choose the
number of channels in "Speaker Channels", so refer to it
when performing the settings.
3. Test tones are emitted by the speakers, and firstly the
unit detects the speakers connected and the noise in the
environment.
4. After the results of the above measurements are
displayed, select "Next", press ENTER on the remote
controller, and the test tones are emitted again, and the
unit automatically makes settings such as the optimum
volume level.
5. When the measurement is completed, the measurement
result is displayed. (For Crossover, the values most suited
to the included speaker system, set up for you beforehand,
are displayed.) Press the cursors
controller to check the settings. Select "Save" and press
ENTER to save the settings.
6. Select whether to enable or disable the equalizer
function that corrects for distortion caused by the
acoustic environment of the room.
If this is to be enabled, then normally you should select "On
(All Channels)", and to disable just the front speakers you
should select "On (Except Front Left / Right)".
7. Disconnect the speaker setup microphone.
∫ 2. Source Connection
Check that each input source is connected correctly. Follow
the guidance, select the input you want to confirm, start
play of the selected player, and confirm that the images
appear on the TV and that sound is played.
∫ 3. Network Connection
Set up Wi-Fi connection with an access point such as a
wireless LAN router. There are the following two methods of
connecting by Wi-Fi:
"Scan Networks": Search for an access point from this
unit. Find out the SSID of the access point beforehand.
"Use iOS Device (iOS7 or later)": Share the iOS device's
Next
Wi-Fi settings with this unit.
> Playback
If you select "Scan Networks", there are a further two
choices of connection method. Check the following.
"Enter Password": Enter the password (or key) of the
access point to connect.
"Push Button": If the access point has an automatic
connection button, you can connect without entering a
password.
0 If the SSID of the access point is not displayed, then in
the screen listing the SSIDs, select "Other..." with the
cursor on the remote controller and press ENTER, then
follow the onscreen instructions.

Keyboard Input

/ on the remote
To switch between upper and lower case, select "A/a" on
the screen and press ENTER. To select whether to mask
the password with " " or display it in plain text, press
MEMORY on the remote controller. Press CLEAR to delete
all the input characters.
0 A confirmation screen asking you to agree to the privacy
policy is displayed during network setting. Select
"Accept" and press ENTER to indicate agreement.
∫ 4. Multi Zone Setup
When you want to enjoy audio in a room other than the main
room, set the audio output method for the separate room
(ZONE 2). If you have connected speakers in a separate room
with speaker cable, select "Using AV Receiver". If you have
connected a pre-main amplifier in a separate room with an
analog audio cable, select "with External Premain Amplifier".
∫ 5. Audio Return Channel
If you have connected a TV that supports ARC, select
"Yes". This unit's ARC setting turns on and you can listen to
the TV's audio through this unit.
0 If you select "Yes", the HDMI CEC function is enabled
and power consumption increases during standby.