Optional Accessories - Makita AN560 Manual De Instrucciones

recoil. In order to avoid this unexpected nailing,
perform as follows;
- Do not place the contact element against the
workpiece with excessive force.
- Pull the trigger fully and hold it on for 1-2 seconds
after nailing.
• Do not operate the tool without nails. It shortens the life
of the tool.
• Make sure all safety systems are in working order
before operation. (Fig. 13)
- Only pulling trigger without contact element
contacting workpiece must not bring about the tool
firing. (Fig. 14)
- Only contact element contacting workpiece without
pulling trigger must not bring about the tool firing.
Driving nails (Fig. 15)
Place the contact element against the workpiece and pull
the trigger, or pull the trigger first and then place the
contact element against the workpiece. (Fig. 16)
The first method is for intermittent nailing, when you wish
to drive a nail carefully and very accurately.
The second method is for continuous nailing.
Use of sequential trip trigger (accessory)
To drive a nail, you may place the contact element against
the workpiece and pull the trigger.
CAUTION:
• WITH THE TRIGGER HELD IN A HALF-PULLED
POSITION, an unexpected nailing could occur, if
contact element is allowed to re-contact against the
workpiece or the other surface under the influence of
recoil. In order to avoid this unexpected nailing,
perform as follows;
- Do not place the contact element against the
workpiece with excessive force.
- Pull the trigger fully and hold it on for 1-2 seconds
after nailing.
Jammed nailer
CAUTION:
• Always disconnect the air hose and remove the nails
from the magazine before cleaning a jam. (Fig. 17)
When the nailer becomes jammed, do as follows:
Open the magazine cap and remove the nail coil. Insert a
small rod or the like into the ejection port and tap it with a
hammer to drive out the nail jamming from the ejection
port. Reset the nail coil and close the magazine cap.
Direction of exhaust air (Fig. 18)
The direction of exhaust air can be changed 360 degrees
of angle by turning the exhaust cover with a hand.
MAINTENANCE
CAUTION:
• Always disconnect the air hose from the tool before
attempting to perform inspection or maintenance.
• Never use gasoline, benzine, thinner, alcohol or the
like. Discoloration, deformation or cracks may result.
Maintenance of nailer (Fig. 19)
Always check the tool for its overall condition and loose
screws before operation. Tighten as required.
With tool disconnected, make daily inspection to assure
free movement of the contact element and trigger. Do not
use tool if the contact element or trigger sticks or binds.
(Fig. 20)
When the tool is not to be used for an extended period of
time, lubricate the tool using pneumatic tool oil and store
the tool in a safe place. Avoid exposure to direct sunlight
and/or humid or hot environment.
Maintenance of compressor, air set and
air hose (Fig. 21 & 22)
After operation, always drain the compressor tank and the
air filter. If moisture is allowed to enter the tool, it may
result in poor performance and possible tool failure.
(Fig. 23)
Check regularly to see if there is sufficient pneumatic oil in
the oiler of the air set. Failure to maintain sufficient
lubrication will cause O-rings to wear quickly. (Fig. 24)
Keep the air hose away from heat (over 60°C, over
140°F), away from chemicals (thinner, strong acids or
alkalis). Also, route the hose away from obstacles which it
may become dangerously caught on during operation.
Hoses must also be directed away from sharp edges and
areas which may lead to damage or abrasion to the hose.
Handling nails (Fig. 25)
Handle nail coils and their box carefully. If the nail coils
have been handled roughly, they may be out of shape or
their connector breaks, causing poor nail feed. (Fig. 26)
Avoid storing nails in a very humid or hot place or place
exposed to direct sunlight.
To maintain product SAFETY and RELIABILITY, repairs,
any other maintenance or adjustment should be
performed by Makita Authorized Service Centers, always
using Makita replacement parts.

OPTIONAL ACCESSORIES

CAUTION:
• These accessories or attachments are recommended
for use with your Makita tool specified in this manual.
The use of any other accessories or attachments might
present a risk of injury to persons. Only use accessory
or attachment for its stated purpose.
If you need any assistance for more details regarding
these accessories, ask your local Makita Service Center.
• Nails
• Air hoses
• Safety goggles
NOTE:
• Some items in the list may be included in the tool
package as standard accessories. They may differ
from country to country.
9