Operating Features; Programming Your Thermostat - White Rodgers 1F80-361 1F80-361 Instrucciones De Instalación Y Operación

Ocultar thumbs

Contenido

Tabla de contenido

Idiomas disponibles

Step

Press Button(s)

PRGM

and RUN

HOLD*

RUN

* Press

HOLD to advance to next item or TIME to move backwards to previous item

4) 4) 4) 4) 4) Select Energy Management Recovery OFF or ON

Select Energy Management Recovery OFF or ON

Select Energy Management Recovery OFF or ON -

Select Energy Management Recovery OFF or ON

Energy Management Recovery (EMR) causes the thermo-

stat to start heating or cooling early to make the building

temperature reach the program setpoint at the time you

specify. Heating will start 5 minutes early for every 1° of

temperature required to reach setpoint.

Example:

Example: You select EMR and have your heating pro-

Example:

grammed to 65° at night and 70° at 7 AM. If the building

temperature is 65° the difference between 65° and 70° is

5°. Allowing 5 minutes per degree the thermostat setpoint

will change to 70° at 6:35 AM. Cooling allows more time per

degree because it takes longer to reach temperature.

5) 5) 5) 5) 5) Select filter replacement run time

Select filter replacement run time - The thermostat will

Select filter replacement run time

"FLTR"

display "FLTR"

"FLTR"

"FLTR" after a set time of operation. This is a

reminder to change or clean your air filter. This time can be

set from 0 to 1950 hours in 50 hour increments. A selection

of 000 will cancel this feature. When "FLTR"

of 000 will cancel this feature.

you can clear it by pressing HOLD and RUN at the same

time. This resets the timer and starts counting the hours

until the next filter change. Changing the time in the menu

also resets the timer.

6) 6) 6) 6) 6) Select Compressor Lockout LOC OFF or ON

Select Compressor Lockout LOC OFF or ON

Select Compressor Lockout LOC OFF or ON - Selecting

Select Compressor Lockout LOC OFF or ON

LOC ON will cause the thermostat to wait 5 minutes before

turning on the compressor if the heating and cooling sys-

tem loses power. It will also wait 5 minutes minimum

between cooling cycles. This is intended to help protect the

compressor from short cycling. Some newer compressors

already have a time delay built in and do not require this

feature. Your compressor manufacturer can tell you if the

feature is already present in their system. When the com-

pressor time delay occurs it will flash the (snowflake icon)

for about five minutes then turn on the compressor.

7) 7) 7) 7) 7) Select Temperature Display Adjustment 4 LO to 4 HI

Select Temperature Display Adjustment 4 LO to 4 HI

Select Temperature Display Adjustment 4 LO to 4 HI -

Select Temperature Display Adjustment 4 LO to 4 HI

Allows you to adjust the room temperature display 4° higher

or lower. Your thermostat was accurately calibrated at the

factory but you have the option to change the display

temperature to match your previous thermostat.

8) 8) 8) 8) 8) Select F° or C° Readout

Select F° or C° Readout

Select F° or C° Readout - Changes the display readout to

Select F° or C° Readout

Centigrade or Fahrenheit as required.

Configuration Menu

Displayed (Factory Default) Press

HOLD

(0:00)

(FA)

d-L

(ON)

Filter

(000)

(in 50 hour increments)

LOC

(OFF)

0 HI

(0)

(F)

A selection

"FLTR" is displayed,

"FLTR"

to select:

0 to 8 hrs (in

Select temporary Hold time

15 minute increments)

Select FA or SL (Fast or Slow) heating cycle rate

OFF

Select display backlight OFF or ON

OFF

Select Energy Management Recovery OFF or ON

0 to 1950 hours

Select filter replacement run time

Select compressor lockout OFF or ON

4 LO to

Select temperature display adjustment higher or lower

4 HI

Select temperature display to F or C

Returns to normal operation

OPERATING FEATURES

Now that you are familiar with the thermostat buttons and

display, read the following information to learn about the many

features of the thermostat.

• SIMULTANEOUS HEATING/COOLING PROGRAM

SIMULTANEOUS HEATING/COOLING PROGRAM

STORAGE

STORAGE — When programming, you can enter both

STORAGE

your heating and cooling programs at the same time. There

is no need to reprogram the thermostat at the beginning of

each season.

TEMPERATURE OVERRIDE

• TEMPERATURE OVERRIDE

TEMPERATURE OVERRIDE

TEMPERATURE OVERRIDE — Press

display shows the temperature you want. The thermostat

will override current programming and keep the room

temperature at the selected temperature until the next

program period begins. Then the thermostat will automati-

cally revert to the program.

HOLD TEMPERATURE

• HOLD TEMPERATURE

HOLD TEMPERATURE — The thermostat can hold any

HOLD TEMPERATURE

temperature within its range for an indefinite period without

reverting to the programmed temperature. Momentarily

press HOLD button. "HOLD"

the desired temperature by pressing

thermostat will hold the room temperature at the selected

setting until you press RUN button to start program opera-

tion again.

CONFIGURATION MENU

• CONFIGURATION MENU

CONFIGURATION MENU — Allows you to customize

CONFIGURATION MENU

certain thermostat options.

PROGRAMMING YOUR THERMOSTAT

This section will help you plan your thermostat's program to

meet your needs. For maximum comfort and efficiency, keep

the following guidelines in mind when planning your program.

• When heating (cooling) your building, program the

temperatures to be cooler (warmer) when the building is

vacant or during periods of low activity.

• During early morning hours, the need for cooling is

usually minimal.

COMMENTS

"HOLD"

"HOLD" will be displayed. Then choose

"HOLD"

until the

. The

Tabla de Contenido

Tabla de contenido

Operating Features; Programming Your Thermostat - White Rodgers 1F80-361 1F80-361 Instrucciones De Instalación Y Operación

Idiomas disponibles

OPERATING FEATURES

PROGRAMMING YOUR THERMOSTAT

Solución de problemas

Manuales relacionados para White Rodgers 1F80-361 1F80-361

Contenido relacionado para White Rodgers 1F80-361 1F80-361

Tabla de contenido