Hedge Trimmer Safety Rules - McCulloch 2030 Manual Del Usuario

Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

Do not force tool. The correct tools will do the job
better and safer at the rate for which it is designed.
Disconnect the plug from the power source
before making any adjustment, changing
accessories, or storing the tool. Such preventive
safety measures reduce the risk of starting the tool
accidentally.
Store idle tools indoors. When not in use, tools
should be stored indoors in dry, and high or
locked-up lace, out of reach of children.
Maintain tools with care. Keep cutting tools sharp
and clean for best performance and to reduce the risk
of injury. Follow instructions for lubricating and
changing accessories. Inspect tool cord periodically,
and if damaged, have it repaired by an authorized
service facility. Keep handling surface dry, clean, and
free from oil and grease.
Check damaged parts. Before further use of the
tool, a guard or other part that is damaged should be
carefully checked to determine that it will operate
properly and perform its intended function. check for
alignment of moving parts, binding of moving parts,
breakage of parts, mounting, and any other
condition that may affect its operation. A guard or
other part that is damaged should be properly
repaired or replaced by an authorized service center
unless indicated elsewhere in this manual.

HEDGE TRIMMER SAFETY RULES

1.
The Hedge trimmer must not be used by anyone
under the age of 16.
2.
Keep children, other people and pets away from
the trimmer.
3.
Always dress properly, don't wear loose clothing
or jewelry. They can be caught in moving parts.
Use of rubber gloves and substantial footwear is
recommended when working outdoor. Wear
protective hair covering to contain long hair.
4.
Use face or dust mask if operation is dusty.
5.
Do not use the trimmer if the cutting device is
not secured properly or is damaged.
6.
Before starting the trimmer, make sure that the
luttig blade is not touching stones or debris.
7.
When the trimmer is in operation, keep the
cutting section away from all parts of the body.
8.
Do not cut against hard objects. This could cause
injury or damage the trimmer.
9.
Only cut during broad daylight or with
corresponding artificial light.
10.
Don't abuse cord, never carry hedge trimmer by
cord or yank it to disconnect from receptacle.
Keep cord from heat, oil, and sharp edges.
11.
When the trimmer is not in use, store it in a dry
place and out of the reach of children.
12.
The mains voltage must correspond to the one
marked on the technical data plate. Do not use
other sources of power.
13.
Never use the trimmer when it is raining. Try to
prevent it from getting wet or being exposed to
WEAR YOUR
SAFETY GLASSES
AND DUST MASK
humidity. Do not leave it outside overnight. Do
not cut damp or wet grass.
14.
The power supply cable should be checked
regularly and before using it each time make
sure the cable is not damaged or old out. If the
cable is not in good condition, do not use the
trimmer. Take it to an authorized service centre
instead.
15.
Only use an extension cable which is suitable for
outdoor work. Keep it away from the cutting
area, from damp, wet or oily surfaces or with
sharp edges and away from heat and fuels.
16.
Avoid unintentional starting, don't carry
plugged in hedge trimmer with fingers on both
switchs. Be sure switch is off when plugging in.
17.
Do not attempt to remove cut material or hold
material to be cut when blades are moving.
make sure trimmer switch is off when clearing
jammed material from blades. Do not grasp the
exposed cutting blades or cutting edges when
picking up or holding the hedge trimmer.
CAUTION: Blades coast after turn off.
18.
Don't force hedge trimmer, it will do the job
better and with less likelihood of a risk of injury
at the rate for which it was designed.
19.
Stay alert, watch what you are doing. Use
common sense. Do not operate hedge trimmer
when you are tired.
20.
Maintain hedge trimmer with care, keep cutting
blades sharp and clean for best performance
and to reduce the risk of injury. Inspect
extension cord periodically and replace if
damaged. keep handles dry, clean and free from
oil and grease.
SPECIFICATIONS . .2030
Input . . . . . . . . . . . . . . . .120V~, 60Hz, 3.75 Amp
No Load cutting rate . . . .3000/min
Cutting Thickness . . . . . .ø14mm
Blade Length . . . . . . . . . .16" (40mmO
Net Weight . . . . . . . . . . .2.5 Kg
SPECIFICATIONS . .2031
Input . . . . . . . . . . . . . . . .120V~, 60Hz, 3.75 Amp
No Load cutting rate . . . .3000/min
Cutting Thickness . . . . . .ø14mm
Blade Length . . . . . . . . . .18" (450mm)
Net Weight . . . . . . . . . . .2.5 Kg
SPECIFICATIONS . .2032
Input . . . . . . . . . . . . . . . .120V~, 60Hz, 3.75 Amp
No Load cutting rate . . . .3000/min
Cutting Thickness . . . . . .ø14mm
Blade Length . . . . . . . . . .20" (500mm)
Net Weight . . . . . . . . . . .2.5 Kg
2

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

20312032

Tabla de contenido