AEG SRC 4315 CD Instrucciones De Servicio/Garantía página 40

• Insert the plug into a properly installed 230 V, 50 Hz power
socket. Connect the device to the wall power supply by
inserting the plug of the power pack into the DC 6 V socket
(2). The time 0:00 fl ashes in the display. Ensure that the
voltage is the same as that indicated on the model identifi ca-
tion plate.
CAUTION:
• The mains adapter supplied must only be used with this
device. Do not use for other devices.
• You should only use an alternating current adapter with
6 V ( ); any other adapter may damage the device.
NOTE:
If the device is not going to be used for a considerable period
you should remove the mains adapter from the socket.
Inserting the batteries
(Not supplied)
If there is a power cut or the mains plug has been removed
from the power socket, the settings will be retained if the power
reserve batteries are inserted.
1. Open the battery compartment (23) on the bottom.
2. Connect a 9 V, E compound battery to the supply connec-
tion. Please ensure the correct polarity.
3. Close the battery compartment again.
4. If the device is not used for a prolonged period of time,
please take the batteries out in order to prevent leakage of
battery acid.
NOTE:
If the capacity of the battery is coming to the end or if no
power reserve battery has been inserted, the „
fl ashes in the display (14).
CAUTION:
Batteries are not to be disposed of together with domestic
wastes. Dispose of the used batteries at the relevant collection
bin or at your dealer's.
WARNING:
Do not expose the batteries to high temperatures or direct
sunlight. Never throw batteries into the fi re. There is a danger
of explosion!
CD deck transport protection
Please open the CD compartment (15) by pressing the OPEN/
CLOSE (open) button (16). The CD compartment cover swings
out towards the front. Remove the transport protection from the
CD player if present before use.
Setting of the Clock (24 h)
• Press the SET/DISP button (3); only the numbers are still
fl ashing.
• Press the FR/HOUR UP button (17) to set the hours. Keep
the button pressed down until the desired hour is reached.
• Press the FF/MIN. UP (17) button in order to set the minu-
40
05-SRC 4315 CD AEG 40
tes. Keep the button pressed down until the desired minutes
are reached.
NOTE:
After approx. 5 seconds the numbers stop fl ashing and the
time currently displayed is automatically stored.
Setting of the Alarm (24 h)
It is possible to set up to two alarm times as follows:
• Press the SET/DISP button (3) twice. The „ " symbol
appears in the display.
• Then keep the FR/HOUR UP and FF/MIN. UP buttons (17)
pressed to set the desired alarm time.
NOTE:
After approx. 5 seconds the „ " symbol goes off, the
alarm time is automatically stored and the current time is
displayed.
• Press the AL1 button (8); the „ " symbol lights up in the
display. The fi rst alarm time is active.
Setting the Second Alarm Time
• Press the SET/DISP button (3) three times. The „ " symbol
fl ashes in the display.
• Then keep the FR/HOUR UP and FF/MIN. UP buttons (17)
pressed in order to set the desired alarm time.
NOTE: After approx. 5 seconds the „ " symbol stops
fl ashing, the alarm time is automatically stored and the
current time is displayed.
• Press the AL2 button (9); the „ " symbol lights up in the
display. The second alarm time is active.
" symbol
In order to switch off the alarm until the following day please
press the ON/STANDBY button.
Deactivating the Alarm Time
• In order to deactivate the fi rst alarm time, press the AL1
button (8) repeatedly until the symbol is no longer displayed.
• In order to deactivate the second alarm time, press the AL2
button (9) repeatedly until the symbol is no longer displayed.
Radio station tuning
• Turn the device on by the ON/STANDBY button (1). Press
the RADIO/CD/AUX button (7) to select radio mode.
• Press the BAND button (11) to select between FM or AM.
FM (MHz) = FM (frequency modulation),
• Select a station by turning the TUNING control (10). The
display shows the radio frequency and to the left of this the
radio band.
• The FM.ST control lamp „ " (in the display) only lights up
if the selected station is being received in stereo quality. If
reception is too weak and there is noise on the station being
received, this lamp will fl icker. Try to improve reception by
turning, winding and unwinding the mains le . In the case
AM (kHz) = medium wave.
antenna
16.03.2007, 12:29:43 Uhr