Descargar Imprimir esta página

Chicago Pneumatic KA11120BY Manual De Instrucciones página 6

Publicidad

Idiomas disponibles
  • MX

Idiomas disponibles

  • MEXICANO, página 8
6159947560-00
Série B
6 / 20
INSTRUCTIONS
This product is designed for removing or polishing
material using abrasives or polishing attachments. No
other use permitted. For professional use only.
Before servicing the power tool, the supply of
compressed air must be disconnected or shut off.
When disposing of components, lubricants, etc ... ensure
that the relevant safety procedures are carried out.
The tool is designed for a working pressure of 6.3 bar (90
psig). The compressed air must be clean. The installation of
a filter is recommended. For maximum efficiency and
performance, comply with the specification of the air hose.
Drain
the
air
hose
(Refer to figure no.1 for compressed air connection)
Ømini mm = 13 (1/2")
To obtain maximum efficiency from the pneumatic tool,
preserve its features and avoid repeated repairs, a routine
inspection and repair programme are recommended at least
every 500 operating hours or every 6 months as a minimum.
In heavy-duty conditions, the inspection program can be
performed every 3 months.
- Disassemble the tool, clean and check the parts carefully.
-
Check the condition of the bearings and inspect the vanes
for wear and surface condition.
For dust extraction, please contact your local sales.
Check the free speed of the tool at regular intervals and
after each operation or maintenance task. Remove the
abrasive to check the speed. The maximum allowed speed
shown on the tool must not be exceeded and the vibration
level must not be excessive.
This tool is fitted with vanes which can operate without
lubricated air. However, a small amount of oil allows the tool
to provide full power and lengthens its life.
The use of dry air with no trace of oil may reduce the life of
vanes.
Risk of icing
Ice can cause continued running after the start lever has
been released.
Always use a dry air supply to avoid the risk of icing.
© Copyright 2003, GEORGES RENAULT SA, 44230 France
All rights reserved. Any unauthorized use or copying of the
contents or part thereof is prohibited. This applies in particular
©
to trademarks, model denominations, part numbers and
drawings.Use only authorized parts. Any damage or
malfunction caused by the use of unauthorized parts is not
covered by Warranty or Product Liability.
1
before
connecting
the
tool.
7 m max.
KA11120BY – KA11060BY
KA11075BY
DISASSEMBLY AND REASSEMBLY INSTRUCTIONS
Disconnect the machine from the compressed air
supply.
Remove all accessories and support handle.
Extract the rear cap assembly.
Disassembling the turbine:
- Remove the turbine from the housing (34).
- Unscrew the speed governor (22).
Left thread (see figure 2).
- Disassemble the turbine (see figure 3).
CLAMP THE ROTOR SLIGHTLY IN A VICE FITTED WITH LEAD
JAWS to unscrew the pinion.
Angle head assembly: Lubricate the shaft gear (1/2 amount
approximately), and proceed to re-assembly. Apply a small quantity of
"Loctite 243" every 120° on the plug (41) before tightening it to a
torque of 60 N.m.
Reassembling the Turbine :
Proceed in reverse order with respect to disassembly.
Be careful with the direction for assembling the vanes.
Apply a small quantity of "Loctite 243" on the thread of the governor
(22) before tightening it to a torque of 2 N.m. Lubricate the pinion with
the grease left.
Rear cap:
360° adjustable lever.
When re-assembling, position the lugs of the cap (9) on each side of
the identification plate supports. Tighten the nut (8) to a torque of 100
N.m.
Lubricating
the
bevel
Recommended grease: 615 990149 0 (24g) or 615 990148 0 (1Kg).
The use of any other lubricant, in any other amount, will shorten the
life and impair the operation of angle pinions.
2
gear.
Amount
of
grease:
3,5
g.
3

Publicidad

loading

Este manual también es adecuado para:

Ka11075byKa11060by