Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
4.4.1
CAUTION! The cleaner must only
be used with clean water; use of
unfiltered water or corrosive chemicals
will damage the cleaner.
4.5
Turn the motor switch to the "0" position.
FIG. 5B
4.6
Check that the electrical supply voltage and
frequency (Volts/Hz) correspond to those
specified on the cleaner data plate. FIG.4E
If the power supply is correct, you may
now plug in the cleaner.
The cleaner must only be connected to
power sockets with regulation earth con-
nection. A differential safety breaker (30
mA) will increase the safety of operators.
CAUTION! The machine may
cause electrical disturbances
when starting.
4.6.1
If the motor stops and fails to restart, wait
2 to 3 minutes before restarting.
CUTOUT TRIPPED
5
USE
5.1
Turn on the water supply tap fully.
5.2
Release the safety catch FIG.5A, then
press the trigger for a few seconds to
allow air to escape and to discharge
residual pressure in the pipes.
5.3
Keeping the trigger pressed, push the
switch to start the motor. FIG.5B
Turn the pressure control knob to the de-
sired setting. FIG.5C (FOR MODELS
WITH THIS FEATURE).
5.3.1
When re-starting the motor, always
keep the trigger pressed.
5.4
USING DETERGENT
5.4.1
CAUTION: liquid detergent must
be sprayed at low pressure. See
5.5 "Proper use of standard accesso-
ries".
5.4.2
Fill the detergent tank to the level indica-
ted through the inlet. FIG. 5D
5.4.3
Select LOW PRESSURE (see instruc-
tions); the detergent will be sucked up and
mixed with the water, with the suction rate
regulated by the knob provided. FIG. 5F
5.4.4
Now distribute the detergent drawn in and
mixed with water.
5.5
Correct use of standard accessories
FIG.5E
5.5.1
The cleaner is equipped with the adjusta-
ble nozzle, which provides some impor-
tant functions:
5.5.2
LOW PRESSURE operation (for suction
and spraying of detergent).
5.5.3
HIGH PRESSURE operation (for high
pressure washing and rinsing).
5.5.4
Jet adjustment from pencil to fan. (For
5.6
5.6.1
5.6.2
5.6.3
5.6.4
5.7
5.7.1
THERMAL
5.8
5.8.1
5.8.2
5.8.3
5.8.4
5.8.5
5.8.6
5.8.7
5.10
-
-
-
6
6.1
English
models with this feature) FIG.5E
CORRECT USE OF THE ROTARY
NOZZLE (Where fitted)
For increased washing power, use the
rotary nozzle kit as follows:
Turn off the high pressure cleaner
Unscrew the adjustable head and fit the
rotary nozzle onto the lance.
Turn the high pressure cleaner back on.
RECOMMENDED CLEANING PROCE-
DURE
Dissolve dirt by applying detergent with
the fan jet to the dry surface.
On vertical surfaces, work from the bottom
upwards. Leave the detergent to act for 1
to 2 minutes, but do not allow to dry out.
Apply the high pressure jet, keeping the
nozzle at least 30 cm (10 in.) from the sur-
face, working from the bottom upwards.
Avoid allowing the rinsing water to run on
to unwashed surfaces.
STORAGE
Switch off the cleaner.
Turn off the water supply tap.
After use, the detergent residues should
be removed from the tank.
Discharge residual pressure by pressing
the trigger until no more water comes out
of the adjustable nozzle.
Engage the gun safety catch.
Remove the plug from the socket.
Operate
the
cleaner
corrosive/non-toxic antifreeze before sto-
ring for the winter.
USE AND CHARACTERISTICS OF TSS
MODELS FIG.5H with automatic delivery
flow cut-off:
when the trigger is released, the dynamic
pressure automatically cuts out the motor.
when the trigger is pressed the pressure
drop automatically starts the motor and
the pressure is restored with a very slight
delay.
For correct operation of the TSS, once the
trigger has been released it must not be
pressed again for at least 4÷5 seconds.
For correct use of the TSS model cleaner,
do not leave the unit in automatic cut-off
status for more than 10 min.
THREE-PHASE OPERATION
CAUTION: with THREE-PHASE
motor (~ 3) on first use the plug
must be connected with the polarity set
so that the motor fan turns clockwise.
Ensure that this is the case by chec-
king that the motor fan turns in the cor-
rect direction.
3
with
non-
Publicidad
Tabla de contenido
