GNB LP Serie Instrucciones De Utilizacion página 7

Faults / Warnings
If a fault occurs during charge the charge status indicator will show
indication 5 and the LCD display will show a fault code and
description, for example:
Faults permanently stop charge until they are rectified.
If a warning occurs during charge the warning symbol
displayed on the LCD display and the warning code and
description can be accessed by scrolling through the charge
information.
Warnings do not affect the charge procedure.
Fault Codes
F06 No output current
F07 **Incorrect battery
F09 **Bulk charge timeout
F10 **Gassing charge timeout
F12 Configuration error
F13 Thermistor fault
F16 **Battery over temperature
F17 **Auto balance timeout
F18 Battery disconnected
F19 Battery disconnected during cooldown
F20 Battery thermistor error
F21 Over current
F27 Slave 1 incorrect current
F28 Slave 2 incorrect current
F29 Slave 3 incorrect current
F30 Slave 1 temperature fault
F31 Slave 2 temperature fault
F32 Slave 3 temperature fault
Warning Codes
F01 **Over discharged battery
F02 **Deeply discharged battery
F03 **Sulphated battery
F04 Charger overheating
F05 Mains failed during charge
F14 **Watering overdue
(Becomes a fault after 5 cycles)
F23 Batt ID PCB error
F24 Batt ID antenna error
F25 Batt ID tag read error
F26 Batt ID not programmed
Repair
Only suitably qualified personnel should perform repair work
on this equipment.
Use of genuine factory sourced replacement parts is necessary to
ensure CE marking is not invalidated.
Contact your local maintenance facility for assistance or spares,
quoting the charger type and serial number which can be found on
the identification label.
Maintenance
Before carrying out maintenance, isolate the mains supply
and disconnect the battery.
Only suitably qualified
maintenance work on this equipment.
The charger will require little maintenance, but the following
schedule is recommended once a month:
will be
(Becomes a fault if overheating persists)
personnel should perform
(a) Check the condition of all cables, paying particular
attention to the points where cables may be severely
flexed, i.e. at the entry to charger cabinet, charging plugs
and sockets.
(b) Check condition of charging plugs and sockets for wear
and any evidence of overheating, which could ultimately
lead to charger malfunction.
(c) Check that ventilation is not obstructed.
(d) Ensure that all safety covers and panels are correctly in
place.
GNB I.P. recommends that a yearly periodic inspection / test is
performed on this equipment, contact your local agent for details.
Guarantee
See local conditions of sale.
Specification
Input Voltage
Input Frequency
Input Current Model dependant - Specified on charger rating plate
Input Cable
Input Protection
Charge
Characteristic***
Output Voltage***
2.9 meters of heat, oil resistant & flame retardant cable to
Output Cable
Output Current***
Output Protection
IP Rating
Cooling
Chargers must be positioned with at least 200mm of
Ventilation
Ambient
temperature
High visibility tri-colour charge status indicator, 192 x 64
User Interface
^ Not available / shown for LP version
* Optional Item, additional hardware may be required.
** These faults are usually associated with the battery, check
battery condition.
*** Factory set as ordered, stated on rating plate
5
1PH - 230VAC ± 10%
3PH - 400VAC ± 10%
45 – 66Hz
2 meters of flexible PVC cable to BS6500
(Input plug fitted on request)
Replaceable fuse(s) fitted inside the cubicle
Microprocessor controlled –
HP = S, D, L, F, H, G , C, R &
LP = S, D, F & C
Model dependant – 24, 36, 48, 72 & 80V Only
BS6195
Model dependant - 20 to 300A
Replaceable fuse inside the cubicle
IP21
Thermostatically controlled fan
clearance overhead, with the fan and front vents
unobstructed
o
0 – 35 C
Graphic LCD & 5 push buttons
GB
Z