Troubleshooting; Return For Repair; Warranty; Accessories - JB INDUSTRIES ELIMINATOR DV-3E Manual De Instrucciones

TROUBLESHOOTING

SYMPTOM
Pump won't start
Pump won't pull deep vacuum
Oil drips from point where shaft enters the
pump housing
Pump shuts down and will not start
Pump cycles on and off from a completely
cold start and then runs smoothly

RETURN FOR REPAIR

in the event your pump requires repair, please contact JB Customer Service
Department to obtain a Return Goods Authorization (RGA) number Ensure that all
returned products are packed to avoid any damage in shipment Paperwork should
be placed in a separate plastic bag and should include JB's assigned RGA number,
a description of the problem and any customer assigned repair or purchase order
number, if applicable
Contact Customer Service for RGA number:
800 323 0811 Toll
800 552 5593 Toll Fax
Customers in Alaska, Arizona, California, Idaho, Montana, Nevada, Oregon, Utah, and Washington have
the option of sending vacuum pump repairs to JB or Merced.
JB Industries
RGA#_________
601 N Farnsworth Ave
Aurora, IL 60505
630 851 9444 Tel
630 851 9448 Fax

WARRANTY

ELIMINATOR pumps are warrantied against defects in materials and workmanship
for 24 months—not changing oil will void warranty JB products are guaranteed
when used in accordance with our guidelines and recommendations Warranty is
limited to the repair, replacement, or credit at invoice price, (our option) of products
which in our opinion are defective due to workmanship and/or materials In no
case will we allow charges for labor, expense or consequential damage Repairs
performed on items out of warranty will be invoiced on a nominal basis; contact
wholesaler for details Product Warranty Registration, Limited Warranty and OTC
Warranty are available online at www jbind com
JB INDUSTRIES • ELIMINATOR Operating Manual • 800.323.0811 • sales@jbind.com
4
POSSIBLE CAUSE(S)
1 Power cord not plugged in securely
2 Motor switch not on
3 Pump temperature below 30°F
4 Inconsistent line voltage
1 Contaminated oil
2 Oil level too low
3 Air leak in system being evacuated
4 Pump inlet fittings missing or not tightened
5 Coupler slipping
Damaged shaft seal
Thermal overload may be open
1 Oil backed up into cartridge and was being cleared out
2 Pump has not been shut down properly
Merced AC Equipment Service
RGA#_________
805 S Fremont
Alhambra, CA 91803
626 293 5710 Tel
626 289 1961 Fax
CORRECTIVE ACTION
1 Plug power cord in securely
2 Turn motor switch to ON position
3 Warm up pump to 30°F and turn motor switch on
4 Line voltage must be within 10% of 115v
1 Change oil
2 Add oil
3 Locate and repair leak(s)
4 Clean or replace o-ring
5 Tighten coupler setscrews to flats of cartridge and motor
Replace shaft seal
1 Disconnect pump from system
2 Wait approximately 15 minutes for motor to cool
3 Turn pump on
4 If it cycles off again, return pump to factory for repair
1 Remove 1/4" cap
2 Turn pump on

ACCESSORIES

MICRON GAUGES
Part No. Description
DV-40S
Wireless Micron Gauge w/mobile app
DV-41 Digital Micron Gauge
DV-22N Digital Vacuum Gauge
BLACK GOLD VACUUM PUMP OIL
DVO-1 Black Gold Vacuum Pump Oil (Pint; Case of 24)
DVO-12 Black Gold Vacuum Pump Oil (Quart; Case of 12)
DVO-24 Black Gold Vacuum Pump Oil (Gallon; Case of 6)
THE TANK VACUUM PUMP OIL CADDY
DV-T1 Empty tank
OIL MIST FILTER
DV-F6
Oil mist filter 3/8"
DV-F8
Oil mist filter 1/2"
SWIVEL COUPLERS
D10244
1/4" Female swivel coupler
D10266
3/8" Female swivel coupler
P90009 1/4" Replacement o-ring (10 pack)
P90012 3/8" Replacement o-ring (10 pack)
SHUT-OFF VALVE
D10162 1/4" Female QC x 1/4" flare
QUICK COUPLERS
QC-E64 3/8" QC x 1/4" SAE elbow
QC-S64
3/8" QC x 1/4" SAE straight
P90009
1/4" Replacement o-ring (10 pack)
P90012
3/8" Replacement o-ring (10 pack)
VELOCITY RAPID EVACUATION KIT
VL-100
Evacuation kit w/hose and valve core removal tool
JB INDUSTRIES
Form No 10346-308 0217
©2017 JB Industries, Inc Printed in the USA