Manufacturer's Warranty - REMS Mini-Cobra A Instrucciones De Uso

eng
1.2. Capacity
Removal of pipe blockages,
e.g. lavatory, sink, shower, bathtub drains
For pipes
1.3. Electric data
230 V, 50–60 Hz, 620 W, 2.9 A; or 110 V, 50–60 Hz, 620 W, 5.8 A
1.4. Dimensions
1.5. Weight
1.6. Noise information
Emission at workplace
1.7. Vibrations
Weighted effective value of acceleration
2. Operation
Attention! Only operate the tool with both hands, always hold the thrust
handle (1) and machine handle (2) tightly. Note the reaction torque of
the drive machine!
Set the direction ring (3) to cable thrust (arrow up). Press the pushbutton
switch slowly so that the drum turns. Turn the thrust handle (1) clock-
wise until the pipe cleaning cable pushes forward automatically. Push
the pipe cleaning cable forward about 20 cm and insert in the pipe to be
cleaned. Do not tighten the thrust spindle too tight otherwise the pipe
cleaning cable may block and damage the device. Keep a maximum
distance of 20 cm between the end of the pipe/drain and the thrust
housing. If the distance is too great the pipe cleaning cable may loop
(danger of injury). Reduce the speed if you encounter resistance.
Only push the pipe cleaning cable forward to an extent that at least 2
windings remain in the drum when cleaning. If the pipe cleaning cable
is pushed further forward, the motor can no longer retract the cable. The
pipe cleaning cable must then be pushed back about 50 cm by hand.
Then the automatic return starts working again.
After clearing the blockage, set the direction ring (3) to return (arrow
down). Keep a distance of at least 20 cm between the end of the pipe/
drain and the thrust housing. If the pipe cleaning cable protrudes from
the end of the pipe/drain, shut down the drive machine immediately.
Attention! The club head moulded to the pipe cleaning cable may not
get into the thrust gear. The drive machine otherwise blocks abruptly
and the thrust gear, club head and pipe cleaning cable are destroyed.
3. Maintenance
3.1. Maintenance
Pull the mains plug before maintenance work! Keep machine clean.
3.2. Inspection/Repair
Pull the mains plug before inspection/repair work! This work may only
be performed by authorised experts or by trained personnel.
The motor of the drive machine has carbon brushes. These are subject
to wear and must therefore be inspected respectively replaced from time
to time by an authorised REMS after-sales service facility.

4. Manufacturer's Warranty

The warranty period shall be 12 months from delivery of the new product
to the first user but shall be a maximum of 24 months after delivery to the
Dealer. The date of delivery shall be documented by the submission of
the original purchase documents, which must include the date of purchase
and the designation of the product. All functional defects occurring within
the warranty period, which clearly the consequence of defects in produc-
tion or materials, will be remedied free of charge. The remedy of defects
shall not extend or renew the guarantee period for the product. Damage
attributable to natural wear and tear, incorrect treatment or misuse, failure
to observe the operational instructions, unsuitable operating materials,
excessive demand, use for unauthorized purposes, interventions by the
Customer or a third party or other reasons, for which REMS is not res-
ponsible, shall be excluded from the warranty.
Services under the warranty may only be provided by customer service
stations authorized for this purpose by REMS. Complaints will only be
accepted if the product is returned to a customer service station autho-
rized by REMS without prior interference in an unassembled condition.
Replaced products and parts shall become the property of REMS.
The user shall be responsible for the cost of shipping and returning the
Ø 20–50 (75) mm
product.
The legal rights of users, in particular the right to claim damages from the
Dealer, shall not be affected. This manufacturer's warranty shall apply only
to new products purchased in the European Union, in Norway or Swit-
470x290x200 mm
zerland.
5.3 kg
80 dB(A)
2.5 m/s 2
eng