Publicidad
(Fig. 8). Observe all the warning messages
relating to the battery charger in this manual.
►►►5. CONNECTION AND
REPLACEMENT OF THE GAS
CYLINDER
The gas cylinder must be replaced in the open
air, away from heat sources, in an atmosphere
without flames.
Only the following accessories must be used
for connection of the gas cylinder to the heater:
•Liquid gas flexible pipe.
•Liquid gas pressure regulator complete with
safety valve.
CHECK THE INTEGRITY OF THE GAS
SUPPLY PIPE. IF THE GAS HOSE NEEDS
TO BE REPLACED, ONLY USE THE
FLEXIBLE TYPE SUITABLE FOR THE
PRESSURE
USED,
NATIONAL REGULATIONS.
►To connect the heater to the gas cylinder:
CAUTION: ALL THREADING IS SINISTRAL,
I.E. THEY ARE TIGHTENED IN AN ANTI-
CLOCKWISE DIRECTION.
►5.1.Screw the gas hose on the heater fitting
(Fig. 9).
►5.2.Install the pressure regulator on the gas
cylinder. Make sure there is a gasket present
on the regulator (if envisioned by the type of
connection) (Fig. 10).
►5.3.Connect the gas hose to the pressure
regulator (Fig. 11).
►5.4.Open the gas cylinder cock (Fig. 12).
►5.5.Press the regulator release button (Fig.
13). Check the tightness of fittings using
soapy water: bubbles indicate a gas leak
(Fig. 14). Several gas cylinders can be fitted
together to obtain greater autonomy. The
correct functioning pressure (see data plate
applied to the heater) is given by the regulator
supplied or an equivalent model.
►►►6. ELECTRICAL POWER
SUPPLY
USE ONLY THE POWER SUPPLY METHODS
DESCRIBED BELOW. TO SWITCH TO
ANOTHER POWER SUPPLY METHOD,
FIRST CARRY OUT THE SWITCH-OFF
REFERRING
TO
PROCEDURE (Par. "9. SWITCH-OFF"). IT
IS PROHIBITED TO CHANGE THE POWER
SUPPLY METHOD WHEN THE HEATER IS
RUNNING.
►►6.1. HEATER POWERED WITH THE
POWER SUPPLY UNIT (when applicable):
THE
CONNECTION
ELECTRICITY
MUST
COMPLIANCE
WITH
STANDARDS IN FORCE.
Before connecting the heater to the mains,
make sure that:
►6.1.1.The electricity mains is equipped with
a differential switch and suitable earth.
►6.1.2.The
power
frequency are correct (see the data plate
affixed to the power supply unit).
Connect the power supply unit to the heater
(Fig. 15) and then connect the power supply
unit to the mains (Fig. 16).
►►6.2. HEATER POWERED WITH THE
RECHARGEABLE BATTERY (when
applicable):
USE ONLY ORIGINAL RECHARGEABLE
BATTERIES WITH THE VOLTAGE RATING
INDICATED ON THE TECHNICAL DATA
PLATE AFFIXED TO THE HEATER.
Insert the rechargeable battery in the battery
compartment under the base of the heater
(Fig. 17).
The rechargeable battery (provided in the
pack and/or on request, depending on the
model) is provided partially charged. In order
to guarantee the full power of the rechargeable
battery, charge it fully using the original battery
charger before initial use (each battery needs
its specific battery charger). The rechargeable
battery has an "NTC" temperature control
device that permits charging only within the
temperature range of 0 and 40°C. This ensures
the long life-span of the rechargeable battery.
►►6.3. HEATER POWERED WITH THE
POWER SUPPLY UNIT AND WITH THE
BATTERY INSERTED (when applicable):
Connect the power supply unit to the heater
(Fig. 15) and then connect the power supply
unit to the mains (Fig. 16) (see the data
plate affixed to the heater). The heater
TO
THE
MAINS
BE
MADE
IN
THE
NATIONAL
supply
voltage
and
en
it
de
es
fr
nl
pt
da
fi
no
sv
pl
ru
cs
hu
sl
tr
hr
lt
lv
et
ro
sk
bg
uk
bs
el
zh
Publicidad
