Safety Instructions; Using The Remote Control Unit; How To Install Batteries; Temperature Sensor Selector (Sensor) - Technibel KPAV122C5TA Serie Instrucciones De Uso

SAFETY INSTRUCTIONS

G
Read this booklet carefully before using this air conditioner.
If you still have any difficulties or problems, consult your
dealer for help.
G
This air conditioner is designed to give you comfortable
room conditions. Use this only for its intended purpose as
described in this Instruction Manual.
EG
WARNING
G Never use or store gasoline or other flammable vapor or liquid
near the air conditioner. It is very dangerous.
Moreover, never install electrical equipment, which is not
protected with IPX1 protection (protection against vertical
water drop), under the unit.
G The manufacturer assumes no responsabilities if the safety
regulations or local codes are not observed.
CAUTION
G Never use the power main switch to start or stop the air
conditioner: always use the ON/OFF button on the remote
control unit or the selector switch on the unit.
G
Do not stick anything into the air outlet of the air conditioner.
This is dangerous because the fan is rotating at high speed.
G
Do not let children play with the air conditioner.
G
Do not cool the room too much if babies or invalids are
present.

USING THE REMOTE CONTROL UNIT

HOW TO INSTALL BATTERIES

G Slide the lid of the remote control
unit following the indication and
remove it.
G Insert two AAA alkaline batteries
of 1,5 V-DC.
Make sure the batteries point in
the direction marked in the
battery compartment.
G
The batteries last about six
months. Depending on how
much you use the remote control
unit.
Remove the batteries if you do
not use the remote control unit
for more than one month.
Press the ACL button using a thin object, e.g. the point of a
pencil or a pen, after batteries replacement.
(This operation allows you to reset correctly all the programs.
The remote control unit is to be set up again).
Replace the batteries when the remote control unit lamp fails
to light, or when the air conditioner does not receive the remote
control unit signals.

TEMPERATURE SENSOR SELECTOR (SENSOR)

G Under normal conditions the room temperature is detected and
checked by the temperature sensor placed in the remote control
unit.
G This button activates the temperature sensor placed in the
indoor unit. Press this button
using a thin object, e.g. the
point of a pencil or a pen. The
display will show the mark
The air conditioner will be set
according to the intake air
temperature of the unit (mean
temperature of room air).
NOTE
For normal use it is recommended the temperature sensor in
the remote control unit to be activated.
ACL BUTTON
.
The remote control unit sends the
temperature signal to the air
conditioner regularly at three
minute intervals. If the signal from
the remote control unit stops for
more than ten minutes due to
some troubles, the air conditioner
will switch to the temperature
sensor which is built into the
indoor unit and controls the room
temperature. In these cases, the temperature around the
remote control unit may differ from the temperature detected
in the air conditioner position.

REMOTE CONTROL UNIT LOCATION

The remote control unit may operate either from a non-fixed
position or from a wall-mounted position. To ensure that the air
conditioner operates correctly, DO NOT install the remote control
unit in the following places:
G In direct sunlight.
G Behind a curtain or other places where it is covered.
G More than 8 m. away from the air conditioner.
G In the path of the air conditioner airstream.
G Where it may become extremely hot or cold.
G Where it may be subject to electrical or magnetic noise.
G Where there is an obstacle between the remote control unit
and the air conditioner (a check signal is sent from remote
control unit every 3 minutes).
1. Wall-mounted non-fixed position
• Momentarily place the remote control unit
in the desired mounting position.
• Verify that the remote control unit can
operate from this position.
• Fix the support at the wall with two screws
and hang the remote control unit.
2. Wall-mounted fixed position
• Momentarily place the remote control unit in the desired
mounting position.
• Verify that the remote control unit can operate from this
position.
• Fix the support at the wall with one screw.
• Remove the batteries from the remote control unit.
• Locate the pretrimmed hole in the battery compartment.
• Through the pretrimmed hole fix the remote control unit at
the wall using the supplied screw.
• Insert the two batteries, check that the remote control unit
operates correctly.
(1)
SUPPORT

OPERATION WITH THE REMOTE CONTROL UNIT

CAUTION
Check that circuit breaker on the power panel is turned ON and
the operation selector of the indoor unit is in the ON position.

HOW TO USE THE REMOTE CONTROL UNIT

When using the remote control unit, always point the unit trasmitter
head directly at the air conditioner receiver.
TRANSMITTER
REMOTE
HEAD
CONTROL UNIT
4
REMOTE CONTROL UNIT
DISPLAY
REMOTE CONTROL UNIT
(2)
RECEIVER
RECEIVER
TRANSMITTER
REMOTE
HEAD
CONTROL UNIT