Stid ARCS-x35-G/PH5 Guia De Inicio Rapido

13.56 MHz
Desktop Reader
Installation instructions
ARCS-x35-G/PH5
Communication: USB
USB 2.0 cable – Length 1.50m – Connector type A - chip FTDI
Cable output:
If the reader is shipped outside of the STid Software Kit:
- Please, click on this url:
- Download the VCP driver according your operating system.
- Connect the reader to the computer with the USB wire furnished.
- Waiting few seconds that the PC recognizes the USB port.
- Launch the installation.
The operating mode for the Buzzer and LED 1 and 2 can be programmed by a configuration card (R3x & S3x) or controlled by the communication protocol of the
reader (W3x).
R and S readers are configurable with the SCB configuration card or virtual configuration card created with SECard.
▪ If the SCB is compatible with the reader's firmware, the LED lights green and the buzzer beeps five times.
▪ If the SCB is not compatible with the reader's firmware, the LED lights red and the buzzer is activated for 1 s.
Caution: set your reader with your own company key.
On power-up, the reader enters an initialization phase:
1. Activation of the white LED and buzzer for 100 ms.
For read-only readers:
2. Activation of the LED, according to the color code: Red = +10, Orange = +5, Green = +1, indicating the firmware version.
3. For serial R/S reader only: the orange LED flashes 20 times: waiting for an update.
4. For ARCS Blue only: Activating white fixed LED during Bluetooth initialization.
5. Activation of the default LED (flashes blue if no customer specific configuration).
Reader power off, the default reader settings can be stored in internal memory accessible by UHF RFID technology. They will be taken into account
when reader is power on.
Caution: at the reader Bluetooth (BT1) powering, make sure that nothing is in an area of at least 10 cm / 3.94 in around the reader (ex. No
hand in front of the reader...).
More details about reader communication are available in SECard User Manual for read only readers or in the protocol specification SSCP for read/write readers.
▪ As far as possible, keep the reader away from computer or power source cables. They can generate electrical interference, depending on their radiation level
and the proximity of the reader.
▪ Recommended distance between two readers: parallel plane: 15.8 in; same plane: 15.8 in; perpendicular plane: 11.8 in// two Blue readers: 6.56 ft either plan.
▪ Readers installed on a metal surface may have reduced performances.
▪ Operating temperature: -4 °F to 158 °F / -20°C to +70°C.
General tolerance following ISO NFT 58-000 standard.
STid declares that the ARCS reader is compliant with the essential requirements of the Directives RED 2014/53/UE and RoHs 2011/65/UE. A copy of our
declaration is available on request from qualite@stid.com.
This device complies with Part 15 of the FCC rules and with ISED's license–exempt RSSs. Operation is subject to the following two conditions:
1) This device may not cause harmful interference.
2) This device must accept any interference received, including interference that may cause undesired operation.
Note: the manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications
could void the user's authority to operate the equipment.
This device complies with the safety requirements for RF exposure in accordance with RSS-102 issue 5 for conditions of use.
In accordance with the provisions of the Environment Code, STid finances the collection, decontamination and recycling of WEEE provided by
ESR-RECYLUM, to which STid adheres and to which it has transferred its regulatory responsibilities as a Producer.
STid recommends that owners of used equipment who wish to dispose of it return it as WEEE by contacting ESR / RECYLUM in order to benefit
from the solutions at no additional cost of collecting and recycling used equipment. More information on www.recylum.fr.
STid reserves the right to make change without notice, for the purpose of product improvement.
13,56 MHz
Lecteur de table
Notice d'installation
ARCS-x35-G/BT1
http://www.ftdichip.com/FTDrivers.htm
Read-only reader configuration
Default parameters configuration
1.09 in
© STid - 20 PA des Pradeaux FR13850 Gréasque - NI1114B03- Page 1 sur 3 - Ed. 27/06/2019
Product references
Characteristics
Driver installation
Buzzer / LED
Powering-up the readers
Caution for Bluetooth reader
Communication
Precautions for installation
Dimensions
3.15 in
Declaration of compliance
"DEEE Pro" Member
13.56 MHz
Lector de mesa
Procedimiento de instalación
conforme con NOM-024 -SCFI-2013
US
FR
ES