Double Insulation; Putting Into Operation - Narex EKK 32 E Instrucciones De Uso

Technical data
Combi Hammer
Model
Voltage.
Frequency.
Input.power.
No-load.speed.
Speed.under.load.
Electronic.speed.control.
Right/Left.rotation.
No-load.impact.rate.
Impact.energy.
Tool.holder.
Drilling.–.ø.max.
. Full.drill:.
. .
. .
. .
. Crown.drill:.
Screw.screws-.ø.max.
. .
. .
Weight.
Protection.class.
Control elements
1 ............Chuck head
2 ............Protective cover
3 ............Locking sleeve
4 ............Locking sleeve of chuck
5 ............Ventilating apertures
6 ............Switch
7 ............Function change over switch
8 ............Push safety
9 ............Switch for change of rotating direction
10 . .........Additional handle
11 . .........Required chuck
12 . .........Holding spindle
13 . .........SDS-Plus chuck
Depicted or displayed accessories need not necessarily become the in-
tegral part of delivery.
Application
Electro pneumatic drilling hammer is a versatile power tool intended for
percussion drilling, medium arduous chiseling to stone, concrete and
wall; wood, metal and plastic drilling and screwing.
This electro pneumatic drilling hammer is intended for professional use
and may be used only for above-mentioned purposes.

Double insulation

To ensure maximum safety of the user, our tools are designed and built
to satisfy applicable European standards (EN standards). Tools with
double insulation are marked by the international symbol of a double
square. These tools must not be grounded and a two-wire cable is suf-
ficient to supply them with power. Tools are shielded in accordance with
EN 55014.
Supplementary handle assembly
Before any interference to the tool, disconnect the supply cable first. Use
the hammer only with supplementary handle (10). Mount the handle to
the fastening neck and secure with revolving grip.

Putting into operation

Connect only to a single-phase alternating current power network with
voltage marked on the nameplate. It is possible to connect the tool even
to outlets without a protective contact, as this is a class II appliance.
.
.
.
.
.
.
.
.
.
.
Steel.
Aluminium.
Wood.
Concrete.
Brickwork.
Wood.
Plate.
.
.
EKK 26 E
30.V
50–60.Hz
900.W
0–70.min
-1
0–615.min
-1


3.800.min
-1
4.8.J
SDS-Plus
16.mm
0.mm
40.mm
3.mm
90.mm
10.mm
8.mm
4.8.kg
II./
Check, if the plug type corresponds with type of the outlet.
Switching ON and OFF
To switch the tool on, push the switch (6) and hold. The hammer switch-
es off as soon as you release the hold of the switch.
Attention: For your safety, it is not possible to secure the switch in
switch on position.
It is forbidden to bypass this safety mechanism.
Function change over switch (7)
The change over switch for switching between drilling, percussion drill-
ing and changing the rotation (7) has four positions.
= drilling,
= percussion drilling,
= rotation switch off, chiseling,
= setting position for chiseling.
The switching between individual functions is best done in still stand mode.
Push safety (8) and turn the change over switch to desired position.
The gear box of the drilling hammer will switch to selected position
when the switch (6) is switched on, that is, after the hammer has been
switched on.
Drilling and percussion drilling
To start drilling, switch the change over switch (7) to
you want to drill with impact, switch to
The switching between individual functions is best done in still stand
mode. Push safety (8) and turn the change over switch to desired posi-
tion.
The gear box of the drilling hammer will switch to selected position
when the switch (6) is switched on, that is, after the hammer has been
switched on.
Attention: When percussion (impact) drilling, do not turn the rota-
tion to the left as this will result in damage to the drill. If you want
to use a diamond drill bit (crown), switch the impact off.
For percussion drilling use only recommended drills with SDS-Plus
clamp stop (shank).
It is not possible to use impact drills with cylindrical stop (shank) in-
tended for quick-change chucks.
English
symbol. If
symbol.
13