Mounting Instruction - Chicago Pneumatic CP87120 Manual Del Operador

EN
English
1. Technical Data (See figure 1.)
Technical Data
Unit
CP87120
All values are current as of the date of this publication. For the latest information please visit www.cp.com.
2. Machine type(s)
• This wheel dolly serves to support during mounting and/or removal of a truck wheel.No other use permitted. For professional use only.
• The dolly is not to be used for transporting wheels over a long distance.
• Please read the instructions carefully before starting the machine.

3. Mounting instruction

Take off the bolts, washers from all parts before assembling.
• Install one caster (O) on the Base (L) with bolts and washers. Fig.01
• Install two Casters (O) on the Adjustable Base(M) with bolts and washers. Fig.02
• Connect Base (L) with Adjustable Base (M) with bolts (M14) and tighten the bolts. Fig.03
• Install one Caster (O) on the Support Tube (K). Fig.04.
• Connect Base Assembly (L) with Support Tube (K), then tighten the bolts. Fig.05.
• Assemble one Roller Table (E) on the Adjustable Base (M) with the Connect Axle (D) and use C Pin (W) to lock. Repeat for another Roller
Table and Support Tube(K). Fig.06.
• Connect Vertical Tube (C) with Base Assembly (L) by pins (I & J) and fix them by R Pin (F). Fig.07.
• Insert Inner Tube (B) into Vertical Tube (C) and insert two Handles (G) into the screw holes on Inner Tube(B). Fig.08.
• Insert Guide Arm (A) into Inner Tube (B). Insert Handle (N) into Base (L).Fig.09.
Caution
Working area of 1 m must be kept free both in front of and behind the machine while it is in operation so that it is always
easily accessible.
4. Operation
Lifting:(fig.10):
Scale: 1:1 Document Ref: 8940169914_REV: 01 _ 05-2012
WARNING
Make sure that lifting only occurs on a flat and strong floor. The wheel/load should be lifted from the floor.
• Place the rollers (E) on either side of the wheel that should be lifted. Move the unit as close to the wheel as possible.
• Adjust the Vertical Tube (C) and Guide Arm (A) to prevent the wheel from dropping during manoeuvring.
• Once the Guide Arm(A) is placed currently, lock its position with handle (G2).
• Don't lock the Handle (G1) while lifting.
• Use the pump handle (N1) to lift the wheel now.
• Before end the lifting procedure,active safety pin(Q),so that the manual safety stop is activated in case of a hydraulic leak.
Lowering:(fig.10):
• Before releasing a load the lock (G1) should be released, allowing Inner Tube (B) to follow the tire down. Also release safety pin (Q).
• Due to the rules of gravity-that the wheel/load overcomes the resistence inside the hydraulic system, the load will be lowered once pressing
the pedal.
• If the load is not big enough or no load ,press the pedal and pump the handle (N1) together to lower the load.
• Stop the lowering movement by releasing the pedal.
WARNING
Before each use, check the dolly for leaks, cracked welds and for damaged, loose or missing parts; if any defects are
found, do not use until repaired.
WARNING
Locate the load centrally on the dolly.
WARNING
Do not exceed the working load limit / rated capacity of the dolly.
WARNING
Never lift people.
WARNING
Operators and maintenance personnel must be physically able to manoeuvre the dolly.
WARNING
Proceed with care in unfamiliar surroundings. Be aware of potential hazards created by your work activity.
WARNING
The product and its accessories must not be modified.
Lifting capacity Stroke
[kg] [mm]
1200 770
Tire Diameter Max Tire Width
[mm]
1000-2200
CP87120
Wheel Dolly
Weight
[mm] [kg]
800 130