Top Panel Overview - Alesis QX61 Guia De Inicio Rapido

TOP PANEL OVERVIEW

14
1
3 4 5
6 7
8
9 10
11
11
13
12
LCD – Displays the data, values, settings, etc. of QX61 and its functions.
1.
KEYBOARD – The KEYBOARD functions as a normal electronic piano keyboard during performance but can
2.
also be used to adjust MIDI settings and send MIDI messages. The labels above the keys indicate their
functions. The numbered keys allow you to enter values for settings. Press the Enter key to confirm your
selections.
ADVANCED – Press this key to access QX61's advanced or secondary functions, allowing you to assign MIDI
3.
channels, set controls, adjust velocity curves, etc. when the ADVANCED button is engaged (i.e., when it is lit).
See the ADVANCED FEATURES section for information on selecting and entering these assignments and
values.
ZONE RNG – Press this button to assign the MIDI note range of a Zone using the KEYBOARD.
4.
ZONE GRP – Press this button then use the TRANSPORT CONTROL buttons to activate/deactivate Zones or
5.
Groups.
-/+ – Decreases/increases the value shown in the LCD by one. You can use these buttons to change the preset
6.
number when storing or recalling presets. Press both buttons simultaneously to activate the Snapshot function,
sending out the current values of the DATA SLIDERS, MODULATION WHEEL, PITCH BEND WHEEL,
KNOBS, and expression pedal (if one is attached).
MUTE – Press this button to disable all of QX61's controls except for the KEYBOARD, pads and transport
7.
controls. "MUTE" will be shown on the LCD. Press MUTE and NULL simultaneously to send a MIDI panic
message, which resets all controls and sends an All Notes Off message.
RECALL – Press this button to recall one of QX61's 20 available presets (01-20). When "RECALL" is flashing
8.
on the LCD, use the -/+ buttons to select a preset. (See ADVANCED FEATURES for more information on
storing presets.) You can press RECALL and PROGRAM simultaneously to set the QX61's global MIDI
channel.
PROGRAM – Press this button to change the current program (0-127). When the button is lit, you can use the -
9.
/+ buttons or the KEYBOARD's numeric keys to change the program number. You can press RECALL and
PROGRAM simultaneously to set the QX61's global MIDI channel.
NULL – Press this button to activate/deactivate Null Mode. ("NULL" will appear on the display when active.) In
10.
Null Mode, when you switch to another preset, QX61's controls will not send out any MIDI data until they reach
the position in which you left them when you last used that preset. Essentially, this feature prevents parameter
values from "jumping" when switching between presets. Press MUTE and NULL simultaneously to send a MIDI
panic message, which resets all controls and sends an All Notes Off message.
OCTAVE/TRANSPOSE UP/DOWN – Press one of these buttons to shift the KEYBOARD's octave range up or
11.
down. Press both buttons simultaneously then press either one of them to shift the KEYBOARD's notes up to
12 semitones in either direction.
PITCH BEND WHEEL – Transmits MIDI Pitch Bend information to raise or lower the pitch of a note
12.
temporarily.
MODULATION WHEEL – This wheel can be used to transmit continuous controller data (CC #1 or Modulation
13.
Depth).
DATA SLIDERS – These sliders let you send MIDI data to adjust their currently selected parameters in your
14.
software.
TRIGGER PADS – These velocity-sensitive pads will send MIDI note messages when pressed. You can use
15.
these pads to trigger drum hits or other samples in your software.
KNOBS – These encoders let you send MIDI data to adjust their currently selected parameters in your
16.
software.
TRANSPORT CONTROLS – You can use these buttons to operate transport controls (play, stop, record, etc.)
17.
in your software. These buttons are also used to select the keyboard's Zones and Groups.
16
15
2
4
17