Sperry instruments Cable-Test TT64200 Instrucciones De Operación

OPERATING INSTRUCTIONS
MODEL: TT64200 Cable-Test™ Cable Tester
Main unit
A
E
B
D
C
F
A. RJ-45 Test Jack
B. Test Shielded Cable
C. Low Battery Indicator
D. Test or Debug Button
E. Cable Select
F. Split Pair Testing
G. T56A or T56B Wiring Chart
SAFETY WARNINGS
This instruction manual contains warnings and safety rules which
must be observed by the user to ensure safe operation of the
instrument and retain it in safe condition. Therefore, read through
these operating instructions before using the instrument.
!
WARNING – Do NoT uSE oN lIvE CIRCuITS
CABlE lENGTh SpECIFICATIoNS
• Min. cable length for testing: 3 feet.
• Max. cable length for testing: 600 feet.
• Maximum Flat Cable Length for cable assembly to attach main unit
or remote to a wall jack or patch panel: 18 inches.
Note: Although the TT64200 is equipped with 8 position modular
plug jacks, cables with smaller 6 position and 4 position connectors
may also be tested. The user should be aware that the use of smaller
connectors will reduce the total number of jack insertions over the life
of the product.
TESTING pATCh CABlES
1. Connect the main unit to one end of the cable to be tested.
2. Connect Remote unit to plug at far end of cable.
3. Push the TEST button to perform test.
4. Read LEDs to determine cable wiring status.
Note: Tester will automatically turn off in 12 seconds.
TESTING INSTAllED CABlES
1. Using the jumper cable, connect the remote unit to the wall jack or
patch panel port to be tested.
2. Using the second jumper cable, connect the main unit to the other
wall jack or patch panel port to be tested.
3. Push the TEST button to perform test.
4. Read status of LEDs to determine cable wiring status.
Note: Tester will automatically turn off in 12 seconds.
TEST RESulTS
PASS Indicators
10 Base-T Token Ring Shield
Two green Two green Green SHIELD
LEDs on Pairs LEDs on Pairs LED indicates the
1-2 and 3-6. 3-6 and 4-5. Shield on the cable
Both pairs Both pairs is correctly and
terminated terminated continuously wired
correctly correctly through the modular
plug termination.
FAIl INDICAToRS
A flashing LED indicates that this wire pair has a fault. A flashing LED
in the FAIL section will indicate which fault was detected. Multiple
flashing LEDs indicate multiple pairs and/or multiple faults. Best
practice is to correct cable faults until cable is verified as correct with
appropriate green LEDs.
• opEN – There is no "OPEN" LED indication. A typical cable may have
2, 3, or 4 pairs. OPENS are displayed as an unlit LED. The user will
determine if a pair is present and continuous or OPEN by comparing
the illuminated LEDs to the expected number of pairs that should
be good. For example, when testing a 4 pair cable, three illuminated
LEDs in the PASS area indicate the presence of an OPEN condition
in one of the pairs.
• ShoRT – A short circuit condition exists.
• MISWIRE – Indicates the improper assignment of individual wire
pairs to pins for the wiring schemes tested. Tester checks T568A,
T568B, 10Base-T, and Token Ring configurations.
• REvERSAl – Reverse wiring means the pin for
one wire in a pair is connected to the opposite pin
for the pair in the remote jack.
Tip
Ring
• SplIT pAIRS – Split pairs occur
when the tip (positive conductor)
and ring (negative conductor) of
two twisted pairs are interchanged.
Remote
• CRoSSovER CABlES – Turn the
A
cable-select switch to
crossover position. Then test
G
as a normal patch cable.
Note: The TT64200 will check
a fault condition in the above
descending order before
detecting other fault conditions.
The detection and indication of the
presence of a fault is handled on a
"one-per-test" basis. Once a fault is
corrected, it is recommended the
cable be tested again for other faults.
DEBuG MoDE
The DEBUG mode identifies which cable pairs have a wiring fault. It
cycles through pairs displaying a test result for one pair at a time. From
the series of LED indications, the failed pair and fault can be identified.
In Debug mode, a short flash on PAIR LED is the pair under test. A
long flash on PAIR LEDs is destination of test.
To DEBUG:
1. Press and hold TEST button until all LEDs light, then release.
2. The pair identification LEDs and the FAIL LEDs work together in
series to identify which pair is incorrect.
3. If a series of two green LEDs light for a pair then that pair is wired
correctly.
4. A green pair LED followed by a red LED in the FAIL section
identifies which pair is incorrect and identifies the fault.
5. DEBUG cycles through the pairs twice before automatically
shutting off.
6. Pushing and quickly releasing the TEST button also turns tester off.
DEBuG Example #1 The Cable Fault is a SHORT on Pair 3-6, the DEBUG
mode LED series will be as follows:
• Pair 1-2 will flash green-green as a good pair
• Pair 3-6 will flash green on the pair LED followed by a red on the
SHORT LED
• Pair 4-5 will flash green-green as a good pair
• Pair 7-8 will flash green-green as a good pair
DEBuG Example #2 Following are some examples of potential
sequences on pair 1-2 and interpretation of various fault conditions for
that pair only:
1st Short
Flash
1-2
1-2
1-2
1-2
1-2
1-2
1-2
1-2
Crossover Cable
Above examples are for 1-2 pair, similar lights would relate to other pairs
under test (short flash)
Four green LEDs
on pairs 1-2,
3-6, 4-5, and 7-8.
loW BATTERY INDICAToR
All four pairs
When the low battery LED lights, replace battery in the main unit. The
are terminated
remote unit does not use a battery.
correctly.
BATTERY REplACEMENT
1. Remove screws from back of main test unit using a #1 Philips
screwdriver. Carefully open tester.
2. Remove old batteries.
3. Install new 6 volt A544 1/2AA size battery or 4LR44 Button cell
batteries.
4. Close tester and replace screws. Do not over tighten.
limited lifetime Warranty limited solely to repair or replacement; no
warranty of merchantability or fitness for a particular purpose. Product
is warrantied to be free of defects in materials and workmanship for the
normal life of the product. In no event shall Sperry Instruments be liable
for incidental or consequential damage.
Marked tip (actually ring)
Roll
Reversed
Marked tip (actually tip)
Split
Tip (first pair)
Pair 1
Pair 2
Ring
Terminal A
1
2
3
4
Crossover cable
5
6
7
8
2nd long Red Fault
Flash LEDs
Fault Condition
1-2 No Red Light Good Pair
None No Red Light Open Condition
1-2 Reversal Pair Reversed 1-2 2-1
1-2 Short Pin 1 Shorted to Pin 2
1-2,3-6 Short 1 or 2 shorted to 3 or 6
7-8 Miswire Pin 1-Pin 7, Pin 2-Pin 8
7-8 Miswire, Reversal Pin 1-Pin 8,Pin 2-Pin 7
Wire from 1-2 twisted with
1-2 Split Pair wire from another pair,
continuity good
INSTRUCCIONES DE OPERACIÓN
MODEL: Cable-Test™ Probador de cables TT64200
unidad principal
A
Ring
Split tip
B
Split tip
Ring
Terminal B
1
2
3
4
5
A. Toma de prueba RJ-45
6
7
B. Probar cable blindado
8
C. Indicador de batería baja
D. Botón de prueba o depuración
ADvERTENCIAS DE SEGuRIDAD
Este manual de instrucciones contiene advertencias y reglas
de seguridad que el usuario debe observar para garantizar el
funcionamiento seguro del instrumento y mantener su estado sin
presentar peligro. Por lo tanto, lea estas instrucciones operativas antes
de usar el instrumento.
! !
ADvERTENCIA – No SE DEBE uSAR EN CIRCuIToS
ENERGIzADoS
ESpECIFICACIoNES DE loNGITuD DEl CABlE
• Largo mín. del cable para pruebas: 91.4 cm.
• Largo máx. del cable para pruebas: 182.8 m.
• Largo máximo del cable plano para el ensamblaje de cables con el fin de
conectar la unidad principal o remota a una toma de pared o panel de
parche: 45.7 cm.
Nota: Aunque el TT64200 está equipado con tomas de enchufe modulares
de 8 posiciones, también pueden probarse conectores más pequeños de 6
posiciones y 4 posiciones. El usuario debe tener presente que el empleo de
conectores pequeños reducirá la cantidad total de inserciones de la toma
durante la vida útil del producto.
pARA pRuEBAS CABlES DE pARChE
1. Conecte la unidad principal a un extremo del cable a probar.
2. Conecte la unidad remota al enchufe del extremo alejado del cable.
3. Pulse el botón TEST (prueba) para realizar la prueba.
4. Lea las luces indicadoras (LED) para determinar el estado del
cableado.
Nota: El probador se apaga automáticamente en 12 segundos.
pARA pRuEBAS CABlES INSTAlADoS
1. Usando el cable puente conecte la unidad remota a la toma de
pared o puerto de panel de parche a probar.
2. Usando el segundo cable puente conecte la unidad principal a la
otra toma de pared o puerto de panel de parche a probar.
3. Pulse el botón TEST (prueba) para realizar la prueba.
4. Lea las luces indicadoras (LED) de estado para determinar cómo está
el cableado.
Nota: El probador se apaga automáticamente en 12 segundos.
RESulTADoS DE pRuEBA
Indicadores de que PASA la prueba
10 Base-T Token Ring
Dos luces Dos luces
indicadoras indicadoras
verdes (LED) verdes (LED)
en pares en pares
1-2 y 3-6. 3-6 y 4-5.
Ambos pares Ambos pares
terminados terminados
correctamente correctamente
INDICADoRES DE FAllA
Una luz indicadora (LED) destellante indica que este par de
cables tiene una falla. Una luz indicadora destellante en la sección
FAIL (FALLA) indica la avería que se detectó. Si hay varias luces
indicadoras destellantes quiere decir que hay varios pares y/o fallas
diversas. Lo mejor es corregir las fallas de cables hasta que se
verifique que los cables están correctos con las luces indicadoras
verdes (LED) adecuadas.
• ABIERTo – No hay indicación de luz indicadora de "OPEN" (abierto).
Un cable típico puede tener 2, 3 ó 4 pares. Los ABIERTOS aparecen
con una luz indicadora (LED) apagada. El usuario determinará si
hay un par presente y continuo o ABIERTO al comparar las luces
indicadoras (LED) iluminadas con el número previsto de pares que
deben estar buenos. Por ejemplo, al probar un cable de 4 pares,
tres luces indicadoras iluminadas en el área PASS (PASA) indican la
presencia de una condición ABIERTA en uno de los pares.
• CoRToCIRCuITo – Existe un cortocircuito.
• CABlEADo INCoRRECTo – Indica la asignación indebida de pares de
cables individuales a patillas para los esquemas de cableado probados. El
probador revisa configuraciones T568A, T568B, 10Base-T y Token Ring.
Remota
A
G
E
D
C
F
1
2
E. Selección de cables 3
1
F. Prueba de pares divididos
4
G. Tabla de cableado T56A o
2
T56B
5
3
6
7
4
8
5
6
7
8
Blindaje Cable de cruce
La luz indicadora Cuatro luces verdes
verde (LED) SHIELD indicadoras (LED)
(blindaje) indica en pares 1-2, 3-6,
que el blindaje 4-5 y 7-8.
del cable está Los cuatro
cableado correcta pares tienen
y continuamente terminaciones
a través de la correctas.
terminación del
enchufe modular.