Publicidad
Idiomas disponibles
Idiomas disponibles
Overload protection
W h en t h e tool is operate d in a manner t h at c auses it to
d ra w an abnormall y h ig h c urrent, t h e tool automati c all y
stops w it h out an y in d i c ation. I n t h is situation, turn t h e
tool o f f an d stop t h e appli c ation t h at c ause d t h e tool to
be c ome o v erloa d e d . T h en turn t h e tool on to restart.
Overheat protection
On
W h en t h e tool is o v er h eate d , t h e tool stops automati c all y , an d
t h e batter y in d i c ator blinks about 6 0 se c on d s. I n t h is situa-
tion, let t h e tool c ool d o w n be f ore turning t h e tool on again.
Overdischarge protection
W h en t h e batter y c apa c it y be c omes lo w , t h e tool stops
automati c all y . I f t h e pro d u c t d oes not operate e v en
w h en t h e s w it c h es are operate d , remo v e t h e batteries
f rom t h e tool an d c h arge t h e batteries.
Switch action
Fig.8: 1. S tan d -b y s w it c h 2. P o w er button 3. S u c tion
force adjusting knob
T o start t h e c leaner :
1 .
S et t h e stan d -b y s w it c h to t h e " I " si d e. T h e c leaner
gets into stan d -b y state.
2.
P ress t h e po w er button.
T o make t h e c leaner get into stan d -b y mo d e, press t h e
po w er button again.
T o turn o f f t h e c leaner, set t h e stan d -b y s w it c h to t h e " O " si d e.
The suction power can be adjusted according to your work need.
S uc tion pow er c an be inc reased by turning th e suc tion f orc e
adjusting knob from the
NOTICE:
A l w a y s set t h e stan d -b y s w it c h to t h e " O "
si d e w h en not using t h e c leaner f or long time. T h e
c leaner c onsumes po w er d uring stan d -b y state.
Auto-suction stop during wet
suction operation
Only for the cloth filter model
WARNING:
Do not use for a long time while
the oat is at ork. Using the cleaner with its float at
w ork f or a long time c an c ause o v er h eat, resulting in
t h e c leaner d e f ormation.
WARNING:
Do not pick up foam or soapy
liquid. P i c king up f oam or soap y li q ui d c an c ause
foam to come out of air exit before the float works.
C ontinuing to using in t h is c on d ition ma y c ause an
ele c tri c s h o c k an d breakage o f t h e c leaner.
Auto-suction stop works only when using with the float
and float cage.
The cleaner has a float mechanism that prevents water
f rom immersing into t h e motor w h en pi c king up more
t h an a c ertain amount o f w ater. W h en t h e tank is f ull
an d t h e c leaner no longer pi c ks up w ater, s w it c h o f f t h e
c leaner an d empt y t h e tank.
Blinking
sy mbol to th e
sy mbol.
Locking or unlocking the caster
Fig.9: 1. C aster 2. S topper le v er 3. F R EE position
4. L O C K position
L o c king t h e c aster is c on v enient w h en storing t h e
c leaner, stopping t h e w ork on t h e w a y an d keeping t h e
c leaner still.
T o operate t h e stopper, mo v e it b y h an d .
T o lo c k t h e c aster w it h a stopper, lo w er t h e stopper
le v er an d t h e c aster no longer w ill rotate. T o release t h e
c aster f rom t h e lo c ke d position, raise t h e stopper le v er.
NOTE: W h en mo v ing t h e c leaner, make sure t h at
t h e c aster is unlo c ke d . Mo v ing t h e c leaner w it h t h e
c aster in t h e lo c ke d position ma y c ause d amage to
t h e c aster.
Carriage handle
W h en c arr y ing t h e c leaner, c arr y it b y h ol d ing t h e h an-
d le on t h e h ea d . T h e h an d le is retra c table at t h e h ea d
w h en not in use.
Fig.10
ASSEMBLY
CAUTION:
Always be sure that the tool is
switched off and the battery cartridge is removed
before carrying out any work on the tool.
CAUTION:
Always wear dust mask during
assembly or maintenance.
Installing the po der lter
and pre lter for dry dust)
Optional accessory for cloth filter model
CAUTION:
Never pick up water or other liq-
uids or et dusts hen using the po der lter.
Picking up such things may cause the powder filter
breakage.
To use powder filter:
Remove the float cage and float by removing the
1.
bolts.
Fig.11: 1. F loat 2. F loat c age
Place the prefilter in the tank with aligning the
2.
mounting position markings.
Mount the damper on the powder filter and then
3.
place them in the prefilter with aligning the mounting
position markings.
4.
F inall y , mount t h e tank c o v er an d lo c k it.
Fig.12: 1. T ank c o v er 2. Powder filter (HEPA)
3. D amper 4. Prefilter 5. T ank 6. Mounting
position marking
Before using the po der lter, make
NOTICE:
sure that pre lter and damper are al ays used
together. It is not allowed to install powder filter
solel y .
13 ENGLISH
EPA)
Publicidad
