Setting The Tv System; Cautions On Use - Pioneer X-SMC1-K Manual De Instrucciones

13 Additional information

Setting the TV system

• This setting is available for a disc or USB storage device
content. For iPod/iPhone's TV out setting, operate your
iPod/iPhone.
• If the picture of the disc being played is distorted, switch
the TV system to the one used in your country or region.
• When the TV system is switched, the types of discs that
can be played are limited.
• The factory default setting is AUTO.
Press  STANDBY/ON to turn the unit's
1
power off.
Press  STANDBY/ON while pressing
2
VOLUME +.
Use the buttons on the unit's top panel.
The power turns on and the TV system switches as shown
below.
• AUTO  NTSC
• NTSC  PAL
• PAL  AUTO
Types of Format
discs/files
NTSC
PAL
-
no disc

Cautions on use

When moving this unit
When moving this unit, be sure to first check that there is no
disc loaded and disconnect the iPod/iPhone. Then press
STANDBY/ON on this unit (or STANDBY/ON on the remote
control), wait for the POWER ON indicator on the front panel
display to turn off, then unplug the power cord. Damage may
occur if the unit is transported or moved with a disc inserted,
or when another device is connected to the iPod/iPhone
connector port, USB terminal, or AUX IN mini-plug jack.
Place of installation
• Choose a stable place near the TV or stereo system being
used with this unit.
36
En
Playing setting
NTSC PAL AUTO
NTSC PAL NTSC
NTSC PAL PAL
NTSC PAL NTSC
or PAL
• Do not place this unit on top of a TV or color monitor.
Also install it away from cassette decks and other
devices easily affected by magnetic forces.
Avoid the following locations:
• Places exposed to direct sunlight
• Humid or poorly ventilated places
• Extremely hot places
• Places exposed to vibrations
• Places in which there is much dust or cigarette smoke
• Places exposed to soot, steam or heat (kitchens, etc.)
Do not place objects on this unit.
Do not place any objects on top of this unit.
Do not obstruct the ventilation holes.
Do not use this unit on shaggy rugs, beds, sofas, etc., or
wrapped in cloth, etc. Doing so will prevent the heat from
dispersing, leading to damage.
Do not expose to heat.
Do not place this unit on top of an amplifier or other
component that generates heat. When rack mounting it, to
avoid the heat given off by the amplifier or other audio
component, place it on a shelf below the amplifier.
• Turn off the unit's power when not using it.
• Depending on signal conditions, striped patterns may
appear on a TV screen and noise may enter the sound of
radio broadcasts when the unit's power is on. If this
happens, turn the unit's power off.
About condensation
If this unit is moved suddenly from a cold place into a warm
room (in winter, for example) or if the temperature in the room
in which this unit is installed rises suddenly due to heater
operation, etc., water droplets (condensation) may form
inside (on operating parts and the lens). When condensation
is present, this unit will not operate properly and playback is
not possible. Let this unit stand at room temperature for 1 or
2 hours with the power turned on (the time depends on the
extent of condensation). The water droplets will dissipate and
playback will become possible. Condensation can also occur
in the summer if this unit is directly exposed to the air flow
from an air-conditioner. If this happens, move this unit to a
different place.
Cleaning the product
• Unplug the power cord from the power outlet when
cleaning this unit.
• Clean this unit using a soft cloth. For tough dirt, apply
some neutral detergent diluted in 5 to 6 parts water to a
soft cloth, wring out thoroughly, wipe off the dirt, then
wipe again with a soft, dry cloth.
• Alcohol, thinner, benzene, insecticides, etc., could
cause the print or paint to peel off. Also, leaving rubber
or vinyl products in contact with this unit for long periods
of time could mar the cabinet.
• When using chemical-impregnated wipes, etc., read the
cautions included with the wipes carefully.