Introduction; Operational Parameters; Contents Of Whole House Filter; Tools Recommended For Installation - Watts pure H2O WH-VIH1-SED-A-WHT-HSG Manual De Instalación, Operación Y Mantenimiento

Introduction

Thank you for your purchase of a Watts Pure H2O Whole House
Water Filter. Water quality concerns are quickly becoming more of a
focus for the public. This Watts Pure H2O whole house water filter
has been designed and tested to provide you with a higher quality
of water.
This filter is designed to reduce the amount of sediment that would
normally enter your home water system. Reducing the amount of
sediment in your home water system will allow your fixtures and
water use appliances to work better.
It is important to change out your filters at the recommended inter-
vals as indicated in this system manual. When replacing the filter
elements, pay special attention to any cleaning instructions. Should
you have any further questions please refer to our web site at
www.watts.com/pureh2o or call our customer service department
at 1-978-689-6066.
Operational Paramaters
Operating Temperature: 100°F (37.8°C)
Operating Pressure: 100 psi (7.03 kg/cm²)

Contents of Whole House Filter

Please make sure all of the items listed below are contained in the
box. If any of the items are missing please contact Watts Pure H2O
at 1-978-689-6066 prior to installing.
• Filter housing with built-in By-Pass Valve
• (3) 50 Micron Sediment Filters (One Preinstalled)
• Filter Wrench
• Mounting Bracket
• Whole House Filter Manual

Tools Recommended For Installation

• Hacksaw or Pipe Cutter
• Low Grit Sandpaper
• (2) 3/4" or 1/2" Crescent Wrenches
• Plumber's Tape (also known as Thread Seal Tape)

Prior To Installation

Watts Pure H2O's Whole house filter is designed to be installed on
the main waterline servicing the house. It should be installed indoors
where it is not subject to cold temperatures or long term exposure
to direct sunlight. Watts Pure H2O does not take any responsibility
for the plumbing of the system into the water line. All water filtration
systems must be installed in accordance with local plumbing codes
and regulations.
Note: For installation, you will need to purchase fittings based on
the pipe size and material of the incoming water line that you will be
tapping into.
NOTICE
For copper pipes we recommend using brass 3/4" MPT
x plumbing size (1/2" or 3/4") compression style fittings.
For all other material types, check with your plumbing
professional.
MAXIMUM MINIMUM
40°F (4.4°C)
20 psi (1.40 kg/cm²)
Figure 1: There are several ways to plumb your Whole House Filter into your existing water line.
The diagram above is the basic install layout.
Whole House Filter Installation
Step 1 - Determine placement of the unit. Make sure the installation
location allows for easy servicing of the system, including a
clearance beneath the filter bowl for filter changes.
NOTICE
This unit must be installed vertically with the lid on top.
Step 2 – Shut off main water supply and open a faucet beyond the
connection to relieve water pressure. Then close the faucet
when depressurized.
Step 3 – Make sure water flow direction coincides with the "IN" and
"OUT" ports marked on the unit.
Step 4 – Cut the water line where the Whole House Filter is to be
installed. The amount of pipe to be removed will be depen-
dent on the type of fittings used. Copper pipes need to be
cleaned & de-burred of any imperfections.
NOTICE
If pipes will be sweat soldered, do not connect into the unit
until the pipes have cooled. Make sure to use Teflon tape on
all male pipe threading used.
CAUTION
Make sure not to overtighten threaded port to the unit!
Step 5 – Using the fittings previously purchased, make sure that the
flow direction is correct through the filter system and plumb
the system to the waterline.
2