Salto LA1T05 Serie Guia De Instalacion

SALTO LA1T
0
Installation guide
Eng
Guide d'installation
F
Guía de instalación
E
ANSI A156.13 Grade 1
ANSI handing code
Eng
Hand changing
Eng
1
TORX 10
Door code Mortise code
LH
L
RHR
RH
R
LHR
Installation Installation
Eng F
PREPARING THE DOOR
Eng
Note: if the strike already exists in the door frame, position lock using strike as reference (See strike position on template)
1. Draw horizontal line on both sides and edge of door at the desired height of knob above floor.
2. Draw vertical center line on door edge.
3. Draw vertical line on each side at the proper backset to align the template.
4. Position templates on edge and sides of door.
Mark holes ONLY for each side, and top and bottom holes of mortise cavity on door edge, and holes in the lateral face of the door for
handles, turn piece hole (only needed in inside face).
5. If lock has anti-friction latch, mark proper recess area on door edge template. (See lock body to determine proper side.)
6. Remove template: place lock face against door edge.
Trace outline of faceplate as guide for faceplate routing.
MORTISE THE DOOR
1. Mortise door for lock body and faceplate per instructions on template.
INSTALLING THE LOCK BODY
1. Insert the lock into the cavity.
2. Mark & drill faceplate holes. Fasten with faceplate screws to hold lock in place.
3. For locks with door detector, see 201082 installation guide to connect.
INSTALLING THE STRIKE
1. Refer to template to determine strike location on jamb.
2. Using strike as template, mark and chisel recess.
Drill screw holes and fasten.
3. Gap between door and jamb is between
ADJUST BEVEL
1. Loosen adjustment screws at top and bottom of case.
2. Turn front to desired bevel.
3. Re-tighten adjustment screws.
NOTE:
Holes for the fixation of the SALTO electronic escutcheon are not included in this template. Please use the template included in the escutcheon box.
Installation guide
5xx/LA1T 5xx /LA1T
1
1-1/16" ( 27 )
1-1/4" ( 32 )
LA1T35xx.. mod.
LA1T15xx.. mod.
ANSI code de remise
F
Changement de main
F
2
RH
LH
Instalación
E
3/32" and 7/32"
.
5xx mortise locks for AACC
3
1-1/16" ( 26,5 ) 4-3/8"
9/32" ( 7,1 )
LA1T35xx.. mod.
LA1T15xx.. mod.
8"
( 203 )
27/64"
( 10,7 )
3/4"
( 19 )
Código mano ANSI
E
Cambio de mano
E
4
Adjust bevel
Eng
( 110 )
1-5/8"
( 41,2 )
5/16"
q
6-1/8"
( q 8 )
( 156 )
1-1/2"
( 38,1 )
2-3/4"
( 70 )
LA1T35xx..
AUTOMATIC
3
Ajustement de la têtiere
F
Adjustment screw
Vis d´ajustement
Tornillo de ajuste
Top of Lock
Latèral de la mort
Lateral de la cerra
Pivot lock front
Têtière pivotante
Frente pivotante
C
L
OF
LEVER
C
L
OF
DOOR
EDGE
LA1T05xx..
LA1T15xx..
5
6
Adjuste del frente
E
OF
LEVER
C
L
C
L
OF
BASKSET
P-221378 - ED3. 10/09/2020