Teuco 270 Instrucciones De Montaje página 24

Assembly Instructions Art. 270-271-272
AVVERTENZE
The product must be installed exactly as supplied by Teuco,
otherwise claims under warranty will not be accepted.
The installer must observe the assembly instructions, using
only the tools and materials recommended, and the accessories
supplied with the product.
The product must be installed directly on the floor and
against finished walls.
Electrical connections must be carried out in compliance with
safety regulations governing bathroom installations,
as described in the accompanying installation standards
manual.
Always use NEUTRAL pH (NON ACETIC) SILICONE.
All the fasteners (bags A-B) and accessories needed for
assembly purposes are in the "accessories box or bag".
This manual illustrates the assembly procedure for the
STANDARD version of the product.
This manual constitutes an integral part of the product and
must be kept for future reference.
REMOVING THE BATHTUB PANELS
1
- Remove the screws securing the panels to the frame of the
A
bathtub.
1
- Remove the panels in the sequence indicated, 1-2,
B
gripping at the base and pulling outwards to release the
clips from their sockets.
POSITIONING AND PREPARING THE TUB
2
- Position the bathtub in the selected place and level up,
first by adjusting the outermost feet, then bringing the
middle feet into contact with the floor.
Make the adjustment so as to leave a distance of 15 mm
minimum between the floor and the bottom edge of the
panel to allow for ventilation of the whirlpool system.
DRAIN CONNECTION
3
- Connect the waste to the drain using the trap and flexible
pipe provided.
FITTING THE EQUIPPED COLUMN
4
- To create the necessary space for the next sequence of
A
steps, distance the bathtub from the walls as far as the
flexible waste pipe will allow.
4
- Screw the pins into the holes at the points indicated, from
B
under the rim, using an Allen key.
FITTING THE CROSS RAIL
5
- Fit the fasteners and the bracket to the frame, being careful to
A
assemble the parts as in the drawing, and leave finger tight to
facilitate the following steps.
5
- Slide the rubber seal (1) onto the rail. Connect the rail to
B
the equipped column (2).
5
- Secure the rail to the frame of the equipped column with
C
the screw and washer.
5
- Position the equipped column on the pins, passing the
D
stainless hoses through the hole in the bathtub rim.
24
- 270-271-272 HYDROSHOWER
6
- PLUMBING CONNECTIONS
- Hot water connection.
- Cold water connection.
6 - Connection of vertical massage hose 6.
- 270-271-272 HYDROSHOWER
- ELECTRICAL CONNECTIONS
- Cable for connection to a.c. supply.
T - Cable for connection to alarm system 1
(only if bathroom is equipped with alarm system).
- EQUIPOTENTIAL EARTH CONNECTION
Connect the binding post ( ) to the main earth
node for the bathroom.
Connect the yellow-green cable locatred on the back
panel to the heart terminal ( ), feeding it through the
hole in the bathtub.
FIXING THE EQUIPPED COLUMN TO THE WALL
7
- Apply silicone sealant to the edges of the tub in contact
A
with wall.
7
- Reposition the tub and column against the wall, taking care
B
not to disturb the waste connection made earlier.
7
- Apply sealant to the bottom of the column, as indicated.
C
-
7
Drill the wall, using the slot in the bracket as a guide.
D
-
7
Use the fasteners kit in the accessories bag.
E
Locate the spacer on the masonry plug.
Insert the masonry plug and fix the column to the wall.
7 -
Fit the concealer to the spacer.
F
FITTING THE SIDE PANEL
8
A - Position the side panel-and-channel assembly on the rim of
the bathtub, locating the pins in the relative holes.
8
- Set the panel plumb, and scribe a vertical reference line on the
B
wall.
8
- Remove the panel assembly from the bathtub.
C
8
- Separate the channel from the panel.
D
8
- Offer the channel to the wall along the reference line marked
E
previously.
Drill the wall, using the holes in the channel as a guide.
8
- Apply sealant to the channel:
F
along the entire length offered to the wall, in the recess as
indicated;
fully around the bottom end resting on the tub.
8
- Apply sealant between the corner of the rim and the wall, as
G
indicated.
8
- Position the channel on the bathtub rim and fix to the wall
H
with the plugs and screws
GB