Manupro MPSOR216MM Manual De Instrucciones página 26

6 Only use saw blades recommended by the manu-
facturer.
Saw blades designed to cut wood and similar ma-
terials must comply with EN 847-1.
7 Do not use saw blades made of high-speed alloy
steel (HSS steel).
8 Only use saw blades for which the maximum per-
missible speed is not lower than the maximum
spindle speed of the crosscut, drag and mitre saw
and which are suitable for the material to be cut.
9 Observe the saw blade direction of rotation.
10 Only insertion the saw blade if you have mastered
their use.
11 Observe the maximum speed. The maximum
speed specified on the insertion tool may not be
exceeded. If specified, observe the speed range.
12 Clean grease, oil and water off of the clamping
surfaces.
13 Do not use any loose reducing rings or bushes for
the reducing of holes on saw blades.
14 Make sure that fixed reducer rings for securing the
insertion tool have the same diameter and have
at least 1/3 of the cutting diameter.
15 Make sure that fixed reducer rings are parallel to
each other.
16 Handle insertion tool with caution. They are ideally
stored in the originally package or special contain-
ers. Wear protective gloves in order to improve
grip and to further reduce the risk of injury.
17 Prior to the use of insertion tools, make sure that
all protective devices are properly fastened.
18 Prior to use, make sure that the insertion tool
meets the technical requirements of this electric
tool and is properly fastened.
19 Only use the supplied saw blade for cutting wood,
never for the processing of metals.
20 Only use saw blade diameters in accordance with
the markings on the saw.
21 Use additional workpiece supports, if required for
workpiece stability.
22 Workpiece support extensions must always be
secured and used during work.
23 Replace table inserts when worn!
24 Avoid overheating of the saw teeth.
25 When sawing plastic, avoid melting of the plastic.
Use the appropriate saw blades for this purpose.
Replace damaged or worn saw blades immedi-
ately.
When the saw blade overheats, stop the machine.
Allow the saw blade to cool down before using the
machine again.
Attention: Laser radiation
Do not stare into the beam
Class 2 laser
26 GB
Protect yourself and you environment from ac-
cidents using suitable precautionary measures!
• Do not look directly into the laser beam with un-
protected eyes.
• Never look into the path of the beam.
• Never point the laser beam towards reflecting sur-
faces and persons or animals. Even a laser beam
with a low output can cause damage to the eyes.
• Caution - methods other than those specified here
can result in dangerous radiation exposure.
• Never open the laser module. Unexpected expo-
sure to the beam can occur.
• If you do not use the device for a long time, the bat-
teries should be removed.
• The laser may not be replaced with a different type
of laser.
• Repairs of the laser may only be carried out by the
laser manufacturer or an authorised representative.
Residual risks
The machine has been built according to the state
of the art and the recognised technical safety re-
quirements. However, individual residual risks
can arise during operation.
• Health hazard due to electrical power, with the use
of improper electrical connection cables.
• Furthermore, despite all precautions having been
met, some non-obvious residual risks may still re-
main.
• Residual risks can be minimised if the „safety in-
structions" and the „Proper use" are observed along
with the whole of the operating instructions.
• Do not load the machine unnecessarily: excessive
pressure when sawing will quickly damage the saw
blade, which results in reduced output of the ma-
chine in the processing and in cut precision.
• When cutting plastic material, please always use
clamps: the parts which should be cut must always
be fixed between the clamps.
• Avoid accidental starting of the machine: the operat-
ing button may not be pressed when inserting the
plug in an outlet.
• Use the tool that is recommended in this manual.
In doing so, your machine provides optimal perfor-
mance.
• Hands may never enter the processing zone when
the machine is in operation.
• Release the handle button and switch off the ma-
chine prior to any operations.