Publicidad
Idiomas disponibles
Idiomas disponibles
Item
Description
+ LED OUT
Provides power to the LEDs on a speaker.
- LED OUT
The red (+) and black (-) LED wires must be
connected to the correct ports.
The regulator has two groups of + and - ports to
which the LED wires may connect. You can
connect up to five Fusion Signature Sports
model speakers or subwoofers per group, for a
total of 10 on one regulator.
BLUE
This control switches the LED color on the
speakers between blue and white.
WHITE
DIM INPUT
This control switches between two preset LED
brightness levels. It can be connected to the
boat lighting circuit.
When connected to the boat lighting circuit, the
LEDs on the speakers dim when the boat lights
are turned on. You can adjust the LED
brightness level using the BRIGHTNESS DIM
ON and BRIGHTNESS DIM OFF controls.
Use of these controls is optional.
BRIGHTNESS
This control adjusts the LED brightness when
DIM OFF
the boat lighting circuit is off or the DIM INPUT is
not connected to the lighting circuit.
BRIGHTNESS
This control adjusts the LED brightness when
DIM ON
the boat lighting circuit is on and the DIM INPUT
is connected to the lighting circuit.
3
Test the regulator by powering on the boat and observing the
LEDs on the speakers.
4
Secure the regulator to the mounting surface using the
supplied screws.
Installing the MS-VREG12 Voltage Regulator
Before you permanently install the voltage regulator, you should
select a mounting location, make wiring connections, and test
the wiring connections.
1
After you have selected a mounting location for the regulator
and installed the fuse, route the appropriate cables to the
mounting location.
2
Use a flat-blade screwdriver to connect the detachable
connector on the regulator, based on the diagram and table.
TIP: You can disconnect the connector from the regulator to
access the binding posts more easily.
Item
Description
+ 12V IN
The positive wire from the boat battery.
This wire must be connected through a 5 A fuse
(not included) near the power supply.
You should connect this wire to an isolator switch
or circuit breaker to turn the regulator on and off.
GROUND IN
The negative or ground wire from the boat battery.
+ 12V OUT
The positive wire to the regulated device.
GROUND OUT The negative wire to the regulated device.
3
Test the regulator by turning on the boat and observing the
regulated device.
4
Secure the regulator to the mounting surface using the
supplied screws.
Installation Instructions
Specifications
Model
Specification
All models
Voltage input
Input current
Output current
Size (L × W × H)
Temperature range
Water rating
Compass-safe
distance
LED Voltage
Voltage output
Regulator (SG-
Dim input on, voltage
VREGLED)
and current
Dim input off, voltage
and current
Remote input on,
voltage and current
Remote input off,
voltage and current
Weight
12V Voltage
Voltage output
Regulator (MS-
Weight
VREG12)
Value
From 10.8 to 16 Vdc
3 A max.
1.5 A max.
110 × 62.4 × 23.5 mm
(4.33 × 2.46 × .93 in.)
From 0 to 50°C (from 32
to 122°F)
IEC 60529 IPX2
(Withstands incidental
exposure to dripping
water when installed with
the terminal block
pointing downward.)
20 cm (7.87 in.)
From 5 to 15 Vdc
From 4 to 24 Vdc, less
than 1 mA
From 0 to 3 Vdc, less
than 1 mA
From 4 to 24 Vdc, less
than 1 mA
From 0 to 3 Vdc, less
than 1 mA
100 g (3.53 oz.)
12 Vdc
80 g (2.82 oz.)
3
Publicidad
