Ordering Information - Pima CLV302 Instrucciones De Instalación

o RoHS Compliant
o CE/GCF (Europe)
o DoC (Russia)
o IFETEL/Movistar (Mexico)
o ICASA (South Africa)
o Anatel (Brazil)
o Telefonica (Global)
 Sensitivity
o -110dbm@UMTS 800/850/
900/2100
o -109.5dbm@UMTS 1900
o -109.5dbm@GSM 850
o -108.5dbm@EGSM 900
o -110dbm@ DCS 1800
o -108dbm@PCS 1900
 HSUPA: Release 7 (Category 6+8)
 EDGE: Multi-slot Class 33
 GPRS: Multi-slot Class 33
 UMTS: Release 99/7
 GSM: Release 99/4
 3GPP TS 27.007, 3GPP TS 27.005
Content of the product package
 CLV302 Add-on
How to install the CLV302
Disconnect the VISION from AC power and remove the batteries before installing the CLV302.
Follow the next steps to install the add-on.
1. Make sure the VISION is located away from other transmitting devices, or near large metal objects.
2. Carefully pull out the SIM card tray (no. 3 in the above figure) from the socket, by pressing gently the eject bar (no. 7 in the figure).
3. (U)SIM1 (Main) card into slot 8, and (U)SIM2 (Backup) card into slot 9, with the metal contacts facing downwards and the
Align
angled corner of the card positioned correctly, and carefully insert the tray into place.
4. Connect the antenna to the antenna connector (no. 10 in the figure).
5. Connect the add-on's circuit board connector (no. 12 in the figure) to its socket on the control panel's circuit board.
6. Connect the control panel to power.
7. Use an LCD keypad (not supplied) and set the add-on; see how in the Installation guide.
8. Test the add-on using the
The LEDs
The CLV302 LEDs (no. 11 in the figure) are described in the table below.
Label Color and state
Yellow blinks (64ms On/800ms Off)
LD1 Yellow blinks (64ms On/2000ms Off)
Yellow blinks (64ms On/600ms Off)
LD2 Red
LD3 Green solid
LD4 Blue

Ordering information

 CLV302 Kit: P/N 8300065
 Enhanced AT Commands
 Bands
o 800/850/900/1900/2100MHz
@UMTS
o 850/900/1800/1900MHz @GSM
o HSUPA Release 7 (category 6)
o HSDPA Release 7 (category 8)
o EDGE Multi-slot Class 12
o GPRS Multi-slot Class 12
o UMTS Release 99/7
o GSM Release 99/4
 Voice
o Speech Codec Modes: HR, FR,
EFR, AMR, AMR-WB
o Echo Arithmetic: Echo
Cancellation, Noise Reduction
 Electrical Characteristics
o Output Power:
 Class 3 (24dBm +1/-3dB) for
 Antenna
Test and Diagnostics
menu.
Description
Modem is registered to the network
Modem is not registered to the network
Data transfer
Not in use
Power on
Used by the manufacturer
UMTS bands
 This guide
-2-
 Class E2 (27dBm±3dB) for
GSM850 & EGSM900
 Class E2 (26dBm±3dB) for
DCS1800 & PCS1900
 Class 4 (33dBm ±2dB) for
GSM 850/900
 Class 1 (30dBm ±2dB) for
GSM 1800/1900
o Power consumption
 50μA@power off
 1.1mA@GSM sleep, DRX=9
 1.7mA@UMTS sleep, DRX=9
 240mA@GSM voice (max.)
 490mA@UMTS voice (max.)
 520mA@GPRS data (max.)
 500mA@EDGE data (max.)
 580mA@HSDPA (max.)
 540mA@HSUPA (max.)