Owner's Manual - B&W CM7 Manual De Instrucciones

English

Owner's manual

Dear Customer,
Thank you for choosing B&W. Please read this manual
fully before unpacking and installing the product. It will
help you to optimise its performance. B&W maintains
a network of dedicated distributors in over 60 countries
who will be able to help you should you have any
problems your dealer cannot resolve.
Environmental Information
All B&W products are designed to comply
with international directives on the
Restriction of Hazardous Substances
(RoHS) in electrical and electronic equipment and the
disposal of Waste Electrical and Electronic Equipment
(WEEE). These symbols indicate compliance and that
the products must be appropriately recycled or
processed in accordance with these directives. Consult
your local waste disposal authority for guidance.
Carton Contents
Check in the carton for:
1 Two-part foam plug
1 Accessory pack containing:
4 M6 spike feet
4 Rubber feet
4 Lock nuts (10mm across flats)
and in the CM9 only
1 Plinth
1 Accessory pack containing:
1 Allen key
4 M6 x 35mm screws
4 Plain washers
4 Shakeproof washers
Speaker Installation
The speakers are intended to be floor mounted only. It
is important to ensure that the speakers stand firmly
on the floor using the spike feet supplied whenever
possible. In addition, the taller CM9 should have its
plinth fitted for proper stability.
To attach the plinth, stand the speaker on its top
taking care not to damage the cabinet or the drive
units during handling. Align the plinth with its
attachment holes in the underside of the cabinet,
ensuring that the arrow on the underside of the plinth
points forwards. Secure the plinth using the screws
and washers supplied. Fit the shakeproof washers
between the plain washers and the screw heads.
Tighten the screws using the Allen key supplied.
The spike feet are designed to pierce carpet and rest
on the floor surface. Initially, screw the lock nuts onto
the spikes enough to leave the nuts floating just above
the carpet when the spikes are resting on the floor
beneath. Screw the spikes fully into the threaded
inserts in the base of the CM7 cabinet or the plinth of
the CM9. If the cabinet rocks when placed on the
floor, unscrew the two spikes that do not touch the
2
floor until the cabinet rests firmly without rocking.
Finally, lock the nuts against the cabinet. It may be
more convenient to fit and adjust the spike feet after
speaker positioning has been optimised.
If there is no carpet and you wish to avoid scratching
the floor surface, use either a protective metal disc (a
coin perhaps) between the spike and the floor, or use
the supplied rubber feet. Fit the rubber feet and level
the cabinet in the same manner as with the spike feet.
Speaker Positioning
Adjustment of speaker position following initial
installation will probably further improve the sound
quality and is usually worthwhile.
In either stereo or home theatre installations, try to
ensure that the immediate surroundings of each
speaker are similar in acoustic character. For example,
if one speaker is adjacent to bare walls while the other
is adjacent to soft furnishings and curtains, both the
overall sound quality and the stereo image are likely to
be compromised.
Conventional Stereo Systems
To begin with, the speakers should be positioned
between 1.5m and 3m apart at two corners of an
equilateral triangle completed by the listening area at
the third corner. The speakers should be
approximately 0.5m away from the back wall, and at
least 0.5m away from any side walls. Figure 1a
illustrates this arrangement.
Home Theatre Systems
If the speakers are to be used for the front channels in
a home theatre system, they should be placed closer
together than for 2-channel audio, because the
surround channels tend to widen the image.
Positioning the speakers within approximately 0.5m of
the sides of the screen will also help keep the sound
image in scale with the visual image. As with
conventional stereo positioning, the speakers should
ideally be at least 0.5m away from any side walls. If
the speakers are preferred placed against the back
wall and this location results in over emphasized bass,
see the Fine Tuning section of this manual for
information on using the foam plugs.
Stray Magnetic Fields
The speaker drive units create stray magnetic fields
that extend beyond the boundaries of the cabinet. We
recommend you keep magnetically sensitive articles
(CRT television and computer screens, computer
discs, audio and video tapes, swipe cards and the
like) at least 0.5m from the speaker. LCD and plasma
screens are not affected by magnetic fields.
Connections
All connections should be made with the equipment
switched off.
There are 2 linked pairs of terminals on the back of the
speaker. For conventional connection, the terminal
links should remain in place (as delivered) and just one
pair of terminals connected to the amplifier. For bi-wire
connection, the terminal links should be removed and