Genius GUARD Guía Para El Instalador página 5

230 V~
230V~
Power Supply
(+6%-10%)
Absorbed power
40 W
Fixed light
Intermittent
Lamp
E27 40W Max
Antenna
Optional
Operating ambient-
-20°C +55°C
temperature
Protection class
IP 55
Insulation class
Class II
DESCRIPTION
See figure 1
Pos
a
Cover
b
Lamp-holder board (traditional version)
c
Board with LEDs (LED version)
d
Cover base
e
Right slide
f
Left slide
g
Flashing lamp support
h Cable runner
i
Antenna support
j
Antenna (optional)
INSTALLATION AND CONNECTIONS
Horizontal or upturned fixing ( Fig. 2 ref. d,e and f) is allowed
only in covered areas, e.g. in buried boxes.
To maintain the protection class IP55 the flashing lamp must
be installed on a flat surface. The flashing lamp support must
rest evenly.
The flashing lamp can be installed in different positions (Fig. 2), depending
on installation needs.
For installation proceed as follows:
1. Choose the installation position keeping in mind that:
a– It must be fixed vertically, except for covered areas (Fig. 2).
b– It must be visible from every direction
c– It must not be covered by trees, signs or other objects
d– It must be positioned in the immediate vicinity of the gate
2. Clear the necessary fixing holes, fig. 2.
3. Choose the cable passage areas (power supply and antenna, if used)
among those shown in Fig. 3.
The position a and b refer to two pre-bored holes, which must
be opened.
4. Insert the power cable (and the antenna cable, if used).
5. Fix the support using the wedges Ø5 (Fig. 4).
6. Clear a pre-bored hole at the base of the cover (Fig. 5 ref. a).
7. Clear two holes on the cable runner (Fig. 5 ref. b).
The cable runner is designed for wire passage only.
8. Insert the power cable and connect it to the board (Fig. 6).
To connect the antenna in the LED versions, refer to the paragraph
"Installing the Antenna".
9. Fix the board inside the cover support.
10. Fix the cover support to the base of the flashing lamp (Fig. 7).
11. Position the antenna support (Fig. 8).
12. Install the flashing lamp cover (Fig. 9):
a– The logo on the cover can be placed in four different positions,
separated by 90°.
b– Position the cover with the logo facing the desired position.
c– Turn slightly anti-clockwise until the cover enters its housing.
GUARD
115 V~
115V~
(+6%-10%)
40 W
NO NO
YES YES
E27 40W Max.
Optional
-20°C +55°C
IP 55
Class II
Description
SPECIFICATIONS
MODEL
24 V 12 V
24 V 12 V
15 W 15 W
YES YES
NO NO
E14 15W Max. BA 15S 15W Max.
Optional Optional
-20°C +55°C -20°C +55°C
IP 55 IP 55
Class III Class III
d– Turn clockwise until the cover locks in place.
On the base of the cover there is a locking tab (Fig. 10 ref. a)
which must couple with the opening made in the cover (Fig. 10
ref. b).
13. Install the two front slides (Fig. 11).
INSTALLING THE ANTENNA
F L g
LaShing amp
1. Clear the pre-bored holes, Ø9 (Fig. 12 ref. a b).
2. Install the antenna and the provided accessories (Fig. 12).
3. Insert the antenna cable separating it from the power supply cable.
4. Position the antenna support and then the cover.
The antenna support cannot be removed if the cover is installed.
Led g F
uard LaShing
The LED version is equipped with a built-in antenna. To connect it, proceed
as follows:
1. Make a Ø 12.5 hole in the cover support (Fig. 13 ref. a).
2. Install an M12x1.5 (or PG7) cable runner, not supplied, as shown in
figure 13.
3. Insert the antenna cable and connect it to the dedicated terminals
precisely as shown in figure 13.
To connect the antenna, use a coaxial cable RG58 (not supplied).
r
epLacing the Light buLb
1. Press the locking tab shown in fig. 14 and remove the cover by turning
it anti-clockwise.
2. Replace the light bulb with a new one having the same specifications.
3. Refit the cover.
CE DECLARATION OF CONFORMITY
Manufacturer:
GENIUS S.p.A. con Socio Unico
Address:
Via Padre Elzi, 32 - 24.50 - Grassobbio - Bergamo -
ITALY
Declares that: Flashing lamp mod. GUARD
conforms to the essential safety requirements of the following EEC
directives:
• 2006/95/EC Low Voltage directive
• 2004/108/EC Electromagnetic Compatibility directive
Additional information:
This product underwent a test in a typical uniform configuration (all
products manufactured by GENIUS S.p.A.)
Grassobbio, 28 June 2011
GUARD
Guide for the installer
LED GUARD
230 V~ / 115 V~
230V~ / 115V~
(+6%-10%)
3W
NO
YES
White LED
Built in
-20°C +55°C
IP 55
Class II
uard
L
amp
MAINTENANCE
The Managing Director
Enrico Nardi
Page 5
24 V
24 V
4W
YES
NO
White LED
Built in
-20°C +55°C
IP 55
Class III