Publicidad
Idiomas disponibles
Idiomas disponibles
SPECIFICATIONS
SPECIFICATIONS
SPECIFICATIONS
SPECIFICATIONS
SPECIFICATIONS
ELECTRICAL RATINGS:
ELECTRICAL RATINGS:
ELECTRICAL RATINGS:
ELECTRICAL RATINGS:
ELECTRICAL RATINGS:
Input Voltage:
Input Voltage:
Input Voltage: 18 to 30 VAC, 60 Hz
Input Voltage:
Input Voltage:
Current:
Current:
Current:
Current: 0.2 amp
Current:
Relay Contact Ratings:
Relay Contact Ratings:
Relay Contact Ratings:
Relay Contact Ratings:
Relay Contact Ratings:
Valve Relay: 1.5 amp @ 25 VAC 60 Hz 0.6 PF
Ignitor Relay: 6.5 amp @ 120 VAC 60 Hz-
resistive
Flame Current Requirements:
Flame Current Requirements:
Flame Current Requirements:
Flame Current Requirements:
Flame Current Requirements:
Minimum current to insure flame detection: 2 µA DC*
Maximum current for non-detection: 0.2 µA DC*
Maximum allowable leakage resistance: 100 M ohms
* Measured with a DC microammeter in series with the
flame probe lead
OPERATING TEMPERATURE RANGE:
OPERATING TEMPERATURE RANGE:
OPERATING TEMPERATURE RANGE:
OPERATING TEMPERATURE RANGE:
OPERATING TEMPERATURE RANGE:
-40° to 175°F (-40° to 80°C)
HUMIDITY RANGE:
HUMIDITY RANGE:
HUMIDITY RANGE:
HUMIDITY RANGE:
HUMIDITY RANGE:
To 95% relative humidity (non-condensing)
MOUNTING:
MOUNTING:
MOUNTING:
MOUNTING:
MOUNTING:
Surface mount or 4" x 4" junction box
GASES APPROVED
GASES APPROVED
GASES APPROVED
GASES APPROVED: : : : : Natural, Manufactured, Mixed,
GASES APPROVED
Liquid Petroleum, and LP Gas Air Mixtures.
INSTALLATION
INSTALLATION
INSTALLATION
INSTALLATION
INSTALLATION
MOUNTING AND WIRING
MOUNTING AND WIRING
MOUNTING AND WIRING
MOUNTING AND WIRING
MOUNTING AND WIRING
WARNING
!
Do not use on circuits exceeding specified volt-
Do not use on circuits exceeding specified volt-
Do not use on circuits exceeding specified volt-
Do not use on circuits exceeding specified volt-
Do not use on circuits exceeding specified volt-
age. Higher voltage will damage control and
age. Higher voltage will damage control and
age. Higher voltage will damage control and
age. Higher voltage will damage control and
age. Higher voltage will damage control and
could cause shock or fire hazard.
could cause shock or fire hazard.
could cause shock or fire hazard.
could cause shock or fire hazard.
could cause shock or fire hazard.
CAUTION
!
To prevent electrical shock and/or equipment
To prevent electrical shock and/or equipment
To prevent electrical shock and/or equipment
To prevent electrical shock and/or equipment
To prevent electrical shock and/or equipment
damage, disconnect electric power to system at
damage, disconnect electric power to system at
damage, disconnect electric power to system at
damage, disconnect electric power to system at
damage, disconnect electric power to system at
main fuse or circuit breaker box until installation
main fuse or circuit breaker box until installation
main fuse or circuit breaker box until installation
main fuse or circuit breaker box until installation
main fuse or circuit breaker box until installation
is complete. Failure to earth ground the appli-
is complete. Failure to earth ground the appli-
is complete. Failure to earth ground the appli-
is complete. Failure to earth ground the appli-
is complete. Failure to earth ground the appli-
ance or reversing the neutral and hot wire con-
ance or reversing the neutral and hot wire con-
ance or reversing the neutral and hot wire con-
ance or reversing the neutral and hot wire con-
ance or reversing the neutral and hot wire con-
nection to the line can cause shock hazard.
nection to the line can cause shock hazard.
nection to the line can cause shock hazard.
nection to the line can cause shock hazard.
nection to the line can cause shock hazard.
Shut off main gas to heating system until instal-
Shut off main gas to heating system until instal-
Shut off main gas to heating system until instal-
Shut off main gas to heating system until instal-
Shut off main gas to heating system until instal-
lation is complete.
lation is complete.
lation is complete.
lation is complete.
lation is complete.
Route and secure all wiring as far from flame
Route and secure all wiring as far from flame
Route and secure all wiring as far from flame
Route and secure all wiring as far from flame
Route and secure all wiring as far from flame
as practical to prevent fire and/or equipment
as practical to prevent fire and/or equipment
as practical to prevent fire and/or equipment
as practical to prevent fire and/or equipment
as practical to prevent fire and/or equipment
damage.
damage.
damage.
damage.
damage.
2
Program Key Timing Specifications Quick Reference
Program Key Timing Specifications Quick Reference
Program Key Timing Specifications Quick Reference
Program Key Timing Specifications Quick Reference
Program Key Timing Specifications Quick Reference
Timing and Retry
Timing and Retry
Timing and Retry
Timing and Retry
Timing and Retry
PROGRAM
PROGRAM
PROGRAM
TRIAL
TRIAL
TRIAL
PROGRAM
PROGRAM
TRIAL
TRIAL
KEY
KEY
KEY
KEY
KEY
FOR
FOR
FOR
FOR
FOR
(COLOR)
(COLOR)
(COLOR)
(COLOR)
(COLOR)
IGNITION
IGNITION
IGNITION
IGNITION
IGNITION
RETRIES
RETRIES
RETRIES
RETRIES
RETRIES
A (blue)
4 Sec.
B (red)
4 Sec.
C (green)
7 Sec.
D (violet)
7 Sec.
E (orange)
4 Sec.
F (yellow)
7 Sec.
NOTE:
NOTE:
NOTE: Program keys are lettered and color coded.
NOTE:
NOTE:
NOTE
Replace control as unit –no user serviceable parts.
All wiring should be installed according to local and national
electrical codes and ordinances.
The control may be mounted in any orientation on a conve-
nient surface using two #6 x 5/8" sheet metal screws. If
desired, control can be mounted on a 4" x 4" junction box
using two #8-32 x 5/8" machine screws. The control must
be secured to an area that will experience a minimum of
vibration and remain below the maximum ambient tempera-
ture rating of 175°F. The control is approved for minimum
ambient temperatures of –40°.
Refer to the wiring diagrams and wiring table when connect-
ing the control to other components of the system.
UL approved 105°C rated 18 gauge minimum wire is
recommended for all low voltage connections. UL approved
105°C rated 16 gauge minimum wire is recommended for all
line voltage connections. Refer to table below for recom-
mended terminals to mate with those on the control.
After installation or replacement, follow appliance
manufacturer's recommended installation/service instruc-
tions to insure proper operation.
IGNITOR
IGNITOR
IGNITOR
IGNITOR
IGNITOR
PREPURGE
PREPURGE
PREPURGE
PREPURGE
PREPURGE
WARMUP
WARMUP
WARMUP
WARMUP
WARMUP
0
30 Sec.
45 Sec.
2
30 Sec.
45 Sec.
0
30 Sec.
45 Sec.
2
30 Sec.
45 Sec.
2
30 Sec.
17 Sec.
2
30 Sec.
17 Sec.
Publicidad
