Troubleshooting - Husqvarna HB32 Manual Del Operador

Troubleshooting

Problem
Pump has following
problems: failure to
produce pressure, loss
of pressure, low water
volume.
Detergent fails to mix
with spray.
Engine will not start;
starts and runs rough
or shuts down during
operation.
For all other issues, see an authorized dealer.
Specifications
°
White, 40 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2400 PSI (165 bar) @ 2.5 GPM (9.5 L/min)*
Green, 25° . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2800 PSI (193 bar) @ 2.4 GPM (9.1 L/min)*
°
Yellow, 15 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2800 PSI (193 bar) @ 2.4 GPM (9.1 L/min)*
°
Red, 0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3100 PSI (214 bar) @ 2.1 GPM (7.6 L/min)*
Water Supply Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41°F (5°C) - 100°F (38°C)
min Water Supply Flow Rate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.5 GPM (13.25 L/min)
min Water Supply Pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 PSI (1.38 bar)
Engine Displacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11.58 in
Spark Plug Gap. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.020 in. (0.050 mm)
Oil Capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 oz (0.6 L)
Power Ratings: The gross power rating for individual gasoline engine models is labeled in accordance with SAE (Society of Automotive
Engineers) code J1940 Small Engine Power & Torque Rating Procedure, and is rated in accordance with SAE J1995. Torque values are
derived at 2600 RPM for those engines with "rpm" called out on the label and 3060 RPM for all others; horsepower values are derived
at 3600 RPM. The gross power curves can be viewed at www.BRIGGSandSTRATTON.COM. Net power values are taken with exhaust
and air cleaner installed whereas gross power values are collected without these attachments. Actual gross engine power will be higher
than net engine power and is affected by, among other things, ambient operating conditions and engine-to-engine variability. Given the
wide array of products on which engines are placed, the gasoline engine may not develop the rated gross power when used in a given
piece of power equipment. This difference is due to a variety of factors including, but not limited to, the variety of engine components
(air cleaner, exhaust, charging, cooling, carburetor, fuel pump, etc.), application limitations, ambient operating conditions (temperature,
humidity, altitude), and engine-to engine variability. Due to manufacturing and capacity limitations, Briggs & Stratton may substitute an
engine of higher rated power for this engine.
*This pressure washer is rated in accordance to the Pressure Washer Manufacturers' Association (PWMA) standard PW101-2010
(Testing and Rating Performance of Pressure Washers).
16
Cause
1. Low pressure spray tip installed.
2. Inadequate water supply.
3. Clogged inlet hose screen.
4. Spray tip is obstructed.
5. Connections leak.
6. High pressure hose or spray gun leaks.
1. High pressure spray tip installed.
2. Check ball stuck in detergent
siphoning system.
3. Detergent siphoning tube is clogged or
cracked.
1. Engine switch set to OFF (0) position.
2. Out of fuel.
3. Flooded with fuel.
4. Dirty air filter.
5. Spark plug wire not connected to spark
plug.
Correction
1. Replace with high pressure spray tip.
2. Provide adequate water flow.
3. Check and clean inlet hose screen.
4. Clean spray tip. See Spray Tip Maintenance.
5. Tighten connections or replace o-rings.
6. Replace.
1. Replace with low pressure black spray tip.
2. Free check ball. See Detergent Siphoning
Check Ball.
3. Clean or replace detergent siphoning
tube.
1. Set engine switch to ON (I) position.
2. Fill fuel tank.
3. Wait 5 minutes before starting.
4. Clean or replace air filter.
5. Connect wire to spark plug.
www.husqvarna.com/us
3 (190 cc)