Braun 9 Serie Manual De Instrucciones página 10

Long hair trimmer
To trim sideburns, moustache or beard press the
release button (8) and slide the long hair trimmer (6)
upwards.
Shaving with the cord (not for models 9095cc w&d/
9080s w&d/9040s w&d)
If the shaver has run out of power (discharged), you
may also shave with the shaver connected to an
electrical outlet via the special cord set.
Travel lock
• Activation: By pressing the on/off switch (4) for
3 seconds the shaver is locked. This is confirmed
by a beep sound and the lock symbol in the display.
Afterwards the display turns off.
• Deactivation: By pressing the on/off switch for
3 seconds the shaver is unlocked again.
Manual cleaning of the shaver
(see fig. B/C)
Cleaning under running water
• Switch on the shaver (cordless) and rinse the shaver
head under hot running water until all residues
have been removed. You may use liquid soap
without abrasive substances. Rinse off all foam
and let the shaver run for a few more seconds.
• Next, switch off the shaver, press the release
buttons (2) to remove the Foil & Cutter cassette
(1) and let it dry completely.
• If you regularly clean the shaver under water, then
apply once a week a drop of light machine oil on
top of the Foil & Cutter cassette.
Models 9080s w&d/9040s w&d only: The shaver
should be cleaned after each foam usage.
Cleaning with a brush
• Switch off the shaver. Remove the Foil & Cutter
cassette (1) and tap it out on a flat surface. Using
the brush, clean the inner area of the pivoting
head. Do not clean the cassette with the brush as
this may damage it!
The Foil & Cutter cassette can be attached either
way. There is no impact on the shaving performance.
Clean&Charge Station
9090cc/9075cc/9070cc/9050cc only)
The Clean&Charge Station has been developed for
cleaning, charging, lubricating, disinfecting, drying
and storing your Braun shaver.
14 Station power socket
15 Lift button for cartridge exchange
16 Station-to-shaver contacts
17 Clean&Charge Station display
17a Level indicator
10
(models 9095cc w&d/
17b Status light
17c Cleaning program indicator (models 9095cc w&d/
9090cc/9075cc only)
18 Start button
19 Cleaning cartridge
Installing the Clean&Charge Station (see fig. D)
• Remove the protection foil if any from the
Clean&Charge Station display.
• Press the lift button (15) at the rear side of the
Clean&Charge Station to lift up the housing.
• Hold the cleaning cartridge (19) down on a flat,
stable surface (e.g. table).
• Carefully remove the lid from the cartridge.
• Slide the cartridge from the rear side into the base
of the station until it snaps into place.
• Slowly close the housing by pushing it down until it
locks.
• Connect the station to an electrical outlet by
snapping the special cord set (11) into the power
socket (14).
Charging the shaver in the Clean&Charge
Station (see fig. D)
Insert the shaver head with the front showing and
released head lock into the cleaning station.
Important: The shaver needs to be dry and free
from any foam or soap residue!
The contacts (7) on the back of the shaver need
to align with the contacts (16) in the station. Push
the shaver in the correct position. A beep sound
confirms that the shaver sits properly in the station.
Charging will start automatically.
Cleaning the shaver (see fig. D)
When the cleaning indicator
display, insert the shaver into the Clean&Charge
Station, as described above and press the start
button (18).
The hygiene status will be analyzed and is shown
by the cleaning program indicators (17c) in the
Clean&Charge Station display (models 9095cc w&d/
9090cc/9075cc only).
If status light (17b) does not shine (Clean&Charge
Station switches to stand-by after ca. 10 minutes),
press start button twice. Otherwise cleaning will not
start. For best shaving results, we recommend
cleaning after each shave.
The cleaning process consists of several cycles, in
which cleaning fluid is flushed through the shaver
head. Depending on your Clean&Charge Station
model and/or program selected, the cleaning time
takes up to 3 minutes, followed by an active drying
phase of about 40 minutes, during which a fan is
running.
Afterwards charging will resume, which is indicated
in the shaver display. When the shaver is fully charged
the display turns off.
lights up in the shaver