Safety Advice; Care & Maintenance; Tools & Equipment - Palram Harmony Mythos Hybrid 6'x14' Manual Del Usuario

IMPORTANT
Please read these instructions carefully before you start to assemble this greenhouse.
Keep these
instructions
in
a
safe place
for future
reference.
»
Customer
Service
For assistance
with assembly or for replacement parts
-
please log
onto our website
or
call
our
service line
(number
is
on
the title
page).
Additional information
can be
found
at
our website: www.palramapplications.com
Safety Advice
It
is
of utmost importance to
assemble all
of the parts according to the directions.
Do not skip any step.
We
strongly recommend using work gloves during assembly.
Always wear shoes and safety
goggles when working with extruded aluminium.
If using
a
step ladder or power tools ensure that you follow the manufacturer's safety advice.
Do not touch overhead power cables
with the aluminium profiles.
Do
not
attempt
to assemble the greenhouse
in
windy or wet conditions.
Dispose
of
all plastic bags. Keep
them out of
reach
of
small
children.
Keep children away from the assembly area.
Do
not
lean
against or push the greenhouse during construction.
Do not position your greenhouse
in an area
exposed to excessive wind.
Do
not attempt to assemble this greenhouse if you
are tired, have
taken drugs or
alcohol or if you
are
prone to dizzy
spells.
Hot items such
as
recently
used
grills, blowtorches
etc.
must not
be
stored
in
the
greenhouse. Ensure there are no
hidden
pipes or cables in
the ground before
inserting the
pegs.
This
product
is
designed to
be used
mainly
as a
greenhouse.
Care &
Maintenance
When
your greenhouse
needs
to
be cleaned,
use a
mild detergent solution and
rinse
with
cold
clean water.
DO NOT use
acetone, abrasive cleaners or other special detergents to clean the clear
panels. It
is
recommended to check periodically that roof panels caps (plastic part 329
&
profile
981) are set in place.
»
Tools
&
Equipment
Tape measure
Work gloves
Silicone spray
/
Lubricant
Phillips head screwdriver
Leveler
Rubber mallet
Adjustable Spanner /Wrench
T001
-
Special tool for
Screws 411
and nuts
412
»
Before
Assembly
Selecting
a
site:
-
The greenhouse must
be
positioned
and fixed on
a
flat
level surface.
-
Choose
a
sunny position away from
overhanging trees.
IR
We
strongly recommend this greenhouse
being secured directly to
a
solid concrete
foundation. When doing that
use
the
pre
drilled
holes in
the metal
base.
IR
This
is a
multi-part
assembly best achieved
by
two
people.
Allow
at least
a
half
a
day for
the assembly
process.
IR
Take all
components
& parts
out of the
packages. Sort the parts and check against
the contents parts list.
Parts
should
be
laid out close at hand.
Keep all small parts (screws etc.) in
a
bowl
so
they do not get
lost.
Please
note multi-sided profiles are used in
this greenhouse.
As
a
result some holes in
the profiles
are
not
used
during assembly.
Please
review entire instructions before
starting. Carry out the assembly steps
in
exact order.
»
Notes
During Assembly
Please
note you install the panels
with the
UV
protected
side
out
(marked
with
"THIS
SIDE
OUT")
and peel the film strip covering
the panels.
You may
use
Silicon
lubricant
spray in
order to
help you slide the panels
into the
profiles.
Do not spray the Polycarbonate panels.
Use
a
rubber mallet if necessary.
Steps 23, 28, 36, 42, 46, 48, 49, 58, 62, 66,
71: Please Note!
Each
of the
3
greenhouses
come with
its
compatible panels kit
as
shown
in
the content
list and in
the relevant assembly
steps.
c;)During
assembly you
will encounter the
information icon, please refer to the relevant
assembly step for additional comments and
assistance.
Step
5: Part
994, 995
are in
the back
of
the
greenhouse. Attaching them determines the front
side
of the greenhouse.
Steps
8, 11: The oval hole in
the
crossbars 256
should
always be assembled to the base
of
the greenhouse.
Step 9 Door Assembly: Determines door direction.
Part
987
is
the
side
that the door hinges will
be
located. The
door
can be
installed either
as a
left or
right hand door. These instructions show
a
right
hand
door
assembly.
Window Assembly
Step 31: Decide on the window's location before
assembly.
Window
can be
installed
in
one of the
indicated options.
Step 45:
In case
the
window
doesn't closed properly,
please release
the
screws,
adjust the profile and
tighten the
screw.
AImportant Recommendations
Firmly connect the greenhouse to
a
level position
immediately after completion of the assembly.
In
order to anchor the greenhouse
use
the
designated manufacturer anchoring kit.
Anchoring the greenhouse
can
also be done by
drilling
the base profiles and
fastening it to the
ground using ground
screws
or spikes
(screws
and spikes are not supplied).
Tighten all screws once assembly
is
completed.
Please
note: Anchoring this product to the
ground
is
essential to
its
stability and rigidity.
It
is
required to complete this stage
in
order for
your warranty to
be
valid.
Screws
411
and nuts 412 are used
thruoghout
the assembly process.
Screws 411 are
to
be
assembled from the outside and nuts 412 from the inside of the greenhouse.
Do
not fasten screws and nuts
(411 &
412) more than
23-
turns only.
Do
not
tighten them
until completion of the panels'assembly, if not specified otherwise.
However,
in
some steps, temporary tightening of
a
few screws may be needed to prevent
a
profile from falling.