Device Description - UNIPRODO UNI_COOLER_05 Manual De Instrucciones

EN
e) The device is not a toy. Children must be
supervised to ensure that they do not play with
the device.
2.4. SAFE DEVICE USE
a) Do not use the device if the ON/OFF switch does
not function properly (does not switch the device
on and off). Devices which cannot be switched on
and off using the ON/OFF switch are hazardous,
should not be operated and must be repaired.
b) Disconnect the device from the power supply
before commencement of adjustment, cleaning
and maintenance. Such a preventive measure
reduces the risk of accidental activation.
c) When not in use, store in a safe place, away from
children and people not familiar with the device
who have not read the user manual. The device
may pose a hazard in the hands of inexperienced
users.
d) Keep the device in perfect technical condition.
Before each use check for general damage and
especially check for cracked parts or elements and
for any other conditions which may impact the safe
operation of the device. If damage is discovered,
hand over the device for repair before use.
e) Keep the device out of the reach of children.
f) Device repair or maintenance should be carried
out by qualified persons, only using original spare
parts. This will ensure safe use.
g) To ensure the operational integrity of the device,
do not remove factory-fitted guards and do not
loosen any screws.
h) When transporting and handling the device
between the warehouse and the destination,
observe the occupational health and safety
principles for manual transport operations which
apply in the country where the device will be
used.
i) Do not touch articulated parts or accessories
unless the device has been disconnected from the
power source.
j) Do not leave this appliance unattended while it is
in use.
k) Clean the device regularly to prevent stubborn
grime from accumulating.
l) Do not cover the air intake and outlet.
m) The device is not a toy. Cleaning and maintenance
may not be carried out by children without
supervision by an adult person.
n) It is forbidden to interfere with the structure of
the device in order to change its parameters or
construction.
o) Keep the device away from sources of fire and
heat.
p) Please use extreme caution when moving the
device while the tank is full.
q) Do not move the device with full tank along
sloping or uneven surfaces, subjecting the device
to significant shocks or vibrations.
r) Do not cover the device while it is working, e.g.
with blankets, sheets, etc.
ATTENTION! Despite the safe design of the
device and its protective features, and despite
the use of additional elements protecting the
operator, there is still a slight risk of accident or
injury when using the device. Stay alert and use
common sense when using the device.
10
3. USE GUIDELINES
The product is intended for home use only! The
evaporative air cooler is a device designed to lower
indoor temperature. In addition, the cooled air is
cleaned and humidified
The user is liable for any damage resulting from
unintended use of the device.

3.1. DEVICE DESCRIPTION

1
11
2 16
10
3
9
15
8
4
5
7
6
14
1. Top cover
2. Ice holder
3. Air inlet, side [1]
4. Water inlet
5. Water tank
6. Caster wheel
7. Water level indicator
8. Front panel
9. Air outlet, front
10. Control panel
11. Top cover
12. Air inlet, side [2]
13. Air inlet, rear
14. Drain valve
15. filter
16. Rear panel
Control panel
ATTENTION! This product's view can be found on the
last pages of the operating instructions (pp. 38).
UNI_COOLER_05
A. Timer
B. Cooling
C. Vertical movement
D. Horizontal movement
E. Airflow rate control
F. On/off switch
UNI_COOLER_06
A. Rotation on/off switch (left-right direction)
B. Main on/off switch and airflow rate control
C. Cooling on/off switch
UNI_COOLER_07
A. Ionization
B. Timer
C. Cooling
D. Rotation
E. Airflow rate control
F. On/off switch
UNI_COOLER_08
A. Ionization
B. Timer
C. Cooling
D. Rotation
E. Airflow rate control
F. On/off switch
Remote control (re. selected models)
A
ON/OFF
B
SPEED
C
12
SWING
D
13 TIMER
E
COOL
F
ANION
3.2. PREPARING FOR USE
APPLIANCE LOCATION
The temperature of environment must not be higher
than 40°C and the relative humidity should be less than
85%. Ensure good ventilation in the room in which the
device is being used. There should be at least 10 cm
distance between each side of the device and the wall or
other objects. The device should always be used when
positioned on an even, stable, clean, fireproof and dry
surface, and be out of the reach of children and persons
with limited mental and sensory functions. Position the
device such that you always have access to the power
plug. The power cord connected to the appliance must
be properly grounded and correspond to the technical
details on the product label.
3.3. DEVICE USE
PLEASE NOTE: Check the water level in the tank during
operation. If the water level is too low, the pump can
be damaged.
PLEASE NOTE: Before using the device, make sure the
amount of water in the tank is correct, i.e. within the
min-max range. Optionally, you can also use ice/cooling
cartridges by placing them in the ice holder.
MAX
MIN
11 EN
UNI_COOLER_05
1. Press the ON/OFF button to start the device. The
device will start at the lowest blow rate.
2. Press the UP/DOWN or LEFT/RIGHT button to
activate the vertical or horizontal movement
mode.
3. Press the SPEED button to change the airflow rate
from LOW> MED> HI. Press again to select the
airflow mode (normal or night mode).
4. Press the COOL button to start the cooling mode.
Please note: If there is not enough water in the
tank, the device will display a message prompting
to top it up.
5. Press the TIMER button to set the required
operation time of the device.
UNI_COOLER_06
1. Turn the SPEED knob to the L position to start the
device.
2. Turn the SPEED knob to change the airflow power
from LOW> MED> HI. Set the SPEED knob to OFF
A. On/off switch
to turn off the device.
B. Airflow rate control
3. Set the SWING knob to ON to activate the rotation
C. Rotation
mode.
D. Timer
4. Set the COOL dial to ON to start the cooling mode.
E. Cooling
Please note: Before you start cooling, make sure
F. Ionization
that there is enough water in the tank.
UNI_COOLER_07
1. Press the ON/OFF button to start the device. The
device will start working at the highest blow rate.
2. Press the SWING button to activate the rotation
mode.
3. Press the SPEED button to change the airflow rate
from LOW> MED> HI. Press again to select the
night mode.
4. Press the COOL button to start the cooling mode.
Please note: If there is not enough water in the
tank, the device will display a message prompting
to top it up.
5. Press the ANION button to activate the additional
air refresh mode.
6. Press the TIMER button to set the required
operation time of the device.
UNI_COOLER_08
1. Press the ON/OFF button to start the device. The
device will start at the lowest blow rate.
2. Press the SWING button to activate the rotation
mode.
3. Turn the SPEED knob to change the airflow power
from LOW> MED> HI. Press again to select the
airflow mode (normal or night mode).
4. Press the COOL button to start the cooling mode.
Please note: If there is not enough water in the
tank, the device will display a message prompting
to top it up.
5. Press the ANION button to activate the additional
air refresh mode.
6. Press the TIMER button to set the required
operation time of the device.
3.4. REINIGUNG UND WARTUNG
A. Cleaning the filters and the tank
Please note: It is recommended to clean the filter
and honeycomb panels at least once every two