Genius BRAIN 03 Manual De Instrucciones Para El Uso Y El Mantenimiento página 17
Ocultar thumbs
Ver también para BRAIN 03:
- Instrucciones para el uso (68 páginas) ,
- Instrucciones para el uso (72 páginas)
Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
N.B.:
• Before you begin programming, select the type of operation for the control unit: with or without encoder (see paragraph 6).
During the programming procedure, the control unit memory-stores the opening, closing mechanical stop points and any pause time
before re-closure.
1- Release the gearmotors, locate the leaves at half open point, and re-lock the operators.
2- Power up the control unit and check if value "
3- Press and hold down push-button P2 until the display shows the first parameter and relevant value.
4- Give an OPEN A command with any device connected to this input: the display shows value "
The first manoeuvre performed by the leaves must be closing. If this does not happen, stop the gate movement with a reset pulse. To
do this, make a bridge between the two "RESET" PINS, using the connector (see Fig.5). Cut
power and put the connector back in its normal position (Fig. 5). Then change over the
wires of the motor/s, which had performed the opening operation. Resume the
programming stage from point 1.
5- When the closing mechanical stop point is reached, the gearmotors pause for about 2
seconds, and then restart with a total opening manoeuvre up to the opening mechanical
stop point or up to the relevant limit-switch.
6- If automatic reclosure was not enabled, this means programming has finished, otherwise
the control unit begins counting pause time.
7- When the required time has elapsed, give another OPEN A pulse, and the gate will begin
to close.
8- When the closing stop has been reached, programming has terminated, and the display
shows value "
".
N.B.:
• The display shows value "
• The flashing lamp stays lighted on a fixed light during the entire programming time.
• Leaf movement is decelerated during the programming procedure.
This is a very important device for reasons of safety. Its setting stays unchanged long-term, without wear. It is active during both closing and
opening. When it operates, it reverses gate movement without disabling automatic closing if activated.
If the clutch operates several consecutive times during the closing movement, the control unit goes into STOP status, disabling any
automatic command. If the clutch operates several consecutive times, this means that the obstacle remains and it could be dangerous
to perform any manoeuvre. To restore normal operation, the user must give an OPEN A / OPEN B pulse.
F
U
S
E
P
R
O
T
E
C
I T
F
1
=
T
1
0
A
P
o
w
e
r
s
u
2
5
0
V
-
5
x
2
0
2
4
V
~
10. PROGRAMMING
" is shown on the display.
" during the entire programming procedure.
11. OPERATION OF ELECTRONIC CLUTCH
12. PROTECTION FUSES
O
N
F
U
S
E
P
R
S
p
p
y l
F
2
=
T
0
6 .
3
A
a
2
5
0
V
-
5
x
2
0
a
n
O
T
E
C
I T
O
N
F
U
S
E
u
p
p
y l
t
o
c
c
e
s s
o
r
e i
s
F
3
=
R
0
6 .
3
A
d
b
a
t t
e
y r
-
2
5
0
V
-
5
x
2
0
c
h
a
r
g
e
r
15
", and the leaves begin to move.
P
R
O
T
E
C
I T
O
N
F
U
S
E
F
a l
s
h
n i
g
a l
m
p
F
4
=
R
3
1 .
5
o
u
t
p
u
t
2
5
0
V
-
5
x
ENGLISH
Fig. 5
P
R
O
T
E
C
I T
O
N
A
E
e l
c
r t
c i
o l
c
k
2
0
o
u
t
p
u
t
Publicidad
Tabla de contenido
