Extended Functions; Basic Functions - Faber Symax GV60 Manual De Usuario

Tabla de contenido

Publicidad

Idiomas disponibles
  • MX

Idiomas disponibles

  • MEXICANO, página 21
2.5
Setting the controls on the remote control unit.
2.5.1
Temperature/clock setting (fig 2.1.1)
The alteration of the temperature indication on the display screen
from °C/24hours to °F/12hours and the other way around is done
in the following manner:
Press the
key and the
indication is modified.
2.5.2
Time setting (fig 2.1.2)
Press the
and
key simultaneously, the day indication
will blink now.
Press the
or
key to set the number of the day.
(1=Monday, 2= Tuesday etc.).
Press the
and
key simultaneously, the hour indication
will blink now.
Press the
or
key to set the hour.
Press the
and
key simultaneously, the minutes
indication will blink now.
Press the
or
key to set the minutes.
To confirm press the
and
2.5.3
Setting the transmitter code on the remote
control unit
Press the reset button of the receiver with a pointed object
(fig. 1.2), until the second signal is audible. Now press the
key on the remote control unit, within 20 seconds. If a sound
signal is audible, the transmitter code has been set.
2.5.4
Setting the childproof lock (fig 2.1.3)
To activate the childproof lock press the
simultaneously.
is displayed and the handset is
rendered inoperable, except for the OFF function.
To deactivate the childproof lock press the
simultaneously.
disappears.
2.5.5
Setting one or two key ignition operation
The ignition operate can be set to one or two key operation.
Standard is one key operation.
To set this immediately press the
placing the batteries and wait until 1 or 2 flashes.
Release the key when the desired number flashes.
2.6

Basic functions

2.6.1 Switching on the fire (fig. 2.2.1 and 2.2.2)
One key operation
Press the
key until two short beeps and a blinking series
of lines appears. The fire automatically starts on high setting.
Fires, equiped with step burner, will start in the setting, in
which the fire the last time is switched off
Two key operation
Press the
and
key simultaneously until two short
beeps and a blinking series of lines appears.
The fire automatically starts on high setting.
Fires, equiped with step burner, will start in the setting,
in which the fire the last time is switched off
key simultaneously until the
key simultaneously.
and
key
and
key
key for 10 seconds after
2.6.2
Switching off the fire (fig 2.2.3)
Press the
key and the fire will be switched off completely.
2.6.3
Adjusting the flame height (fig 2.2.4, 2.2.5 and 2.2.6)
Keep the
key pressed to decrease the flame height step
by step or to switch back to pilot flame.
Pressing the
key twice in rapid succession will set the fire
to the lowest position.(LO appears in the display screen)
Keep the
key pressed to increase the flame height step
by step
Pressing the
key twice in rapid succession will set the fire
to the highest position. (HI appears in the display screen)
2.6.4
Switch the Step burner (fig.2.2.7)
>
NOTES:
Only for fires with step burner.
The step burner will not operate for 45 sec. after the start-up
procedure.
Press the
key until
the flame picture will concentrate in the middle of the burner.
Press the
key until
and the flame picture will divide over the complete length of
the burner.
2.6.5
Switch the LED Symbio effect (fig 2.2.8)
>
NOTES:
Only for fires with LED Symbio effect.
The Led Symbio module is independent of the flames and is
equipped with a standard light pattern.
Press the
key until
switch the effect on.
Press the
key until
switch the effect off.
2.7

Extended functions

2.7.1
Countdown timer (fig 2.3.1)
At the end of the countdown time period the fire turns off.
Set and turn on
Press the
key until
the hour indication blinks.
Press the
or
key to set the hour. (max. 9 hours)
To confirm press the
Press the
or
key to set the minutes.
To confirm and start press the
Turn off
Press the
key until
2.7.2
Thermostatic mode (fig 2.3.2 and 2.3.3)
The room temperature is measured and compared to the selected
temperature. The flame height is then automatically adjusted to
achieve the selected temperature.
1 1
appears in the display screen and
disappears in the display screen
appears in the display screen to
disappears in the display screen to
appears in the display screen and
key and the minutes indication blinks.
key or wait a few seconds.
disappears in the display screen.
ENG

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

40011661-1717

Tabla de contenido