Sammic SU-310 Manual De Instrucciones página 7

Indications for CE marking.
Each machine has the following identification
elements:
• Name and address of the manufacturer:
SAMMIC, S.L. Basarte, 1, Azkoitia Gipuzkoa
(SPAIN).
• "CE" mark.
• The machine model is shown in the next
section.
• The serial number is printed on the Guarantee
Card and in the Declaration of Conformity.
MODELS
This manual describes the installation, operation
and maintenance of the sensor controlled
vacuum packing machines:
• bench top models: SU-310, SU-316, SU-416,
SU-420, SU-520
• free-standing models: SU-604, SU-606, SU-
806, SU-810.
• Free-standing, double-chamber models: SU-
6000
• Options for these models:
· Gas : « G » Gas injection system
· Printer: « P » Electronic board with Bluetooth
for connectivity with a smartphone to print
adhesive labels
· Sealing « + » : Select the user at the press of a
button, more sealing power available for metal
bags
The model reference and its specifications
appear on the name plate attached to the
machine.
These packaging machines are designed and
manufactured in accordance with European
directives 89 / 392 / EEC, 93 / 68 EEC, 73 / 23 /
EEC and the NSF health and hygiene standard.
INSTALLATION
For optimum performance and long service life
of the machine, carefully read and follow the
instructions provided in this manual.
Placement
Place the machine so that it is correctly levelled.
To prevent damage, the machine must never
rest on one side.
Bench top machines must be installed on a
smooth surface, since their legs are made of a
sliding material for easy removal of the machine
to clean the supporting surface.
Electrical connection
1. Machine specifications
-A single-phase motor is supplied for operation
on 230V.
-A three-phase motor is supplied for operation
on 230V or 400V (factory-set to 400V).
Before connecting the vacuum packing machine
to the mains, check whether the machine is
prepared for the same voltage as the mains.
To change the voltage setting (only three-phase
machines):
1. Connect the transformers to the corresponding
voltage as indicated on their connection board.
2. If necessary, change if the connections in the
motor as indicated in the terminal box.
3. If necessary, adjust the thermal relay as
indicated on the wiring diagram.
2. Power cable specifications
SAMMIC packaging machines are supplied with
an electric cable 1.5 m long, with plastic thermal
covering.
THE EARTH CONNECTION IS OBLIGATORY.
The machine's earth connection wire is
indicated. The machine is also fitted with
an external screw for the connection to an
equipotential earth connection system
.
- Three-phase machines: Prepare a wall-
mounted mains socket with 3P+N+E, 20 A
magneto-thermal and differential protection,
and a sealed plug to connect it to the power
supply cord of the packing machine.
- Single-phase machines: Prepare a wall-
mounted mains socket with 2P+E, 20 A
magneto-thermal and differential protection.
The plug, which forms part of the power supply
cable, must be accessible.
3. Changing the vacuum pump turning
direction (only in three-phase machines)
If an abnormal noise occurs in the vacuum
pump motor when starting the machine, it is
because it is rotating in reverse. In this case,
stop the machine immediately and exchange
two phases in the power supply.
Oil filling
In models SU-416, SU-420, SU-520, SU-600,
SU-800, the pump already contains oil.
In models SU-310, SU-316, fill the pump with
oil through the inlet, until it reaches ¾ of the
indicator. Detergent-free oil must be used:
-SAE10 Oil (without detergent) for pumps up to
20 m³/h.
-Oil SAE30 (without detergent) for pumps over
20 m ³/h.
It is recommended that the oils used are paraffin.
START-UP
Once the main switch has been turned on,
several cycles must be run empty prior to the
first packaging so that the oil is hot and the
correct vacuum is obtained.
ON/OFF BUTTON:
lights:
• Red on standby with the machine connected
to the network. The machine is switched off in
"OFF".
• When pressed it changes to blue: machine
turned "ON".
If the machine is not used for a period of time,
it will then automatically standby in OFF mode.
OPERATION:
KEY: The following functions are
accessed with each press:
• Vacuum PROGRAMS 1 to 25: The
number of the program accessed with the
keys will flash
• VACUUM BY STAGES: For
porous products, processed meats, emulsified
mixtures with trapped air, etc. Perform these
three steps to reach the vacuum setpoint with
a fixed waiting time in each stage:
E.g. .: if the setpoint is 99%:
· Stage 1: 91%, t = 10s
· Stage 2: 95%, t = 10s
· Stage 3: 97%, t = 10s
· End: 99%
EXTERIOR VACUUM (VAC. NORM):
For special Gastronorm trays for vacuum. In
order to use this function, you need to purchase
the VAC-NORM kit that includes a hose and
connector to the chamber of the vacuum
packing machine.
· Before activating the VAC-NORM function,
place the connector and hose in the machine
suction.
· Place the other end of the hose in the tray.
· When the key is pressed the
pump starts, which operates until the vacuum
reaches the setpoint; it will then stop and
Includes two
EN
7