Publicidad
Idiomas disponibles
Idiomas disponibles
C. Pipe Cutting range:
UPC616A
6" – 16" nominal (150 – 450 O.D. mm)
UPC636A
6" – 36" nominal (150 – 1000 O.D. mm)
UPC648A
6" – 48" nominal Pipe (150 – 1300 O.D. mm)
UPC836APE 8" – 36" nominal PE pipe ONLY (200 – 1000 O.D. mm)
UPC848APE 8" – 48" nominal PE pipe ONLY (200 – 1300 O.D. mm)
d. beveling:
Bevel determined by Bevel Cutter used. Available by
special order.
E. Maximum Cutting depth
4" Blade =
/
23
32
6" Blade = 1
/
23
4" Blade Steel = ½" (12.7 mm)
6" Blade Steel = ½" (12.7 mm)
8" Blade PE = 2
F. standard Equipment
Standard Equipment
Power Cutter with 1.7 H.P. Motor
Chain/Turnbuckle Assembly
cut up to 16"
Connecting Frames & Chain to cut up to
Filter/Regulator/Lubricator with Stand
Water Tank
Carrying Case
Air Line Oil
Grease Gun w/Gear Grease
Hex Key Wrench Set
Open End Wrenches
Wedges
UPCSTEEL6 6" blade
UPCPE8 8" blade
G. Optional Accessories/blades
Use BLADE SELECTION CHART to choose the best blade
for the application. (see below)
h. Auxiliary Equipment required:
Air compressor capable of sustaining 50 SCFM @90 psi.
Hoses equipped with compatible fittings. If fittings other
than those supplied with the motor are used, they should
be a full bore type to maximize motor speed.
iii. AssEMblY
A. blade installation
1. Select a Blade from the Chart Below
2. Install Blades
blAdE sElECtiOn ChArt
Catalog no.
item Code
UPCARB4
97510
UPCBPVC*
97511
UPCARB6
97514
UPCSTEEL4
97519
UPCSTEEL6
97520
UPCPE8**
97521
UPCDIA4
97529
UPCDIA6
97525
* Used with UPCARB4 or UPCARB6 cut-off blades. Long arbor #97561 is required since this bevel cutter has 1¼" blade thickness.
** This blade works only with UPC836 and UPC848 models.
" (18.3 mm)
" (43.6 mm)
32
23
/
" (69 mm)
32
UPC616A UPC636A
UPC648A UPC836APE UPC848APE
YES
YES
YES
YES
YES
YES
NO
36"
48"
YES
YES
YES
3 gallon
6 gallon
6 gallon
w/Cart
w/Cart
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
NO
NO
NO
NO
NO
NO
description
4" BLADES cut up to 23/32" (18.3 mm) wall thickness
PVC Bevel Cutter
6" BLADES cut up to 1 23/32" (43.7 mm) wall thickness
4" BLADES cut up to 1/2" (12.7 mm) wall thickness
4" BLADES cut up to 23/32" (18.3 mm) wall thickness
6" BLADES cut up to 1/2" (12.7 mm) wall thickness
6" BLADES cut up to 1 23/32" (43.7 mm) wall thickness
8" BLADES cut up to 2 23/32" (69 mm) wall thickness
4" BLADES cut up to 23/32" (18.3 mm) wall thickness
6" BLADES cut up to 1 23/32" (43.7 mm) wall thickness
a. Standard Arbor - Install the blade on the
arbor shoulder (Fig. 2). Install the flange with the
relieved side toward the blade and screw on the
locknut. While holding a wrench (supplied) on the
/
7
8
must seat fully on the arbor shoulder and flush
against the face of the arbor.
NOTE: To cut PVC only, without bevel, use standard arbor
#97617 that ships installed with the unit.
b. Long Arbor for Cutting & Beveling PVC
To cut and bevel at one time, install bevel cutter
(small edge toward motor) over Long Arbor #97561.
Next, install selected blade on 5/8 diameter arbor
shoulder (Fig. 3). Install flange washer with relieved
side toward blade and then screw on locknut. While
holding a wrench (supplied) on 7/8 arbor flats,
tighten arbor locknut using 3/4" wrench (supplied).
Blade must seat fully on arbor shoulder and flush
against bevel cutter. See Cut & Bevel PVC Set-up,
Fig. 7 for full details.
YES
YES
c. Guideline for depth when beveling:
YES
YES
6" blade plunge an additional 1.7" after blade
36"
48"
contacts pipe
YES
YES
4" blade plunge an additional 1.1" after blade
NO
NO
contacts pipe
YES
YES
NOTE: Blade life depends on weather conditions, type of
YES
YES
pipe and pipe diameter, and exterior pipe treatments.
YES
YES
YES
YES
CAUTION: Air Motor rotates COUNTERCLOCKWISE as
YES
YES
viewed from the arbor end. Blades stamped with rotation
YES
YES
YES
YES
arrow must be installed so they rotate counterclockwise.
YES
YES
b. installing bevel Cutters (Fig. 1) Optional
1. Check motor tightness by tightening motor clamp screws
(2) on the underside of unit. (Fig. 1)
blade Guard Mounting
blade
Guard
FIG.1
Pipe diameter
6" (150 mm)
6"- 48" (150-1300 mm)
8"- 48" (200-1300 mm)
6" - 8" (150-200 mm)
6" - 8" (150-200 mm)
8" - 48" (200-1300 mm)
8" - 48" (200-1300 mm)
26" - 48" (660-1300 mm)
6" - 8" (150 -200 mm)
8"- 48" (200-1300 mm)
arbor flats, tighten the arbor locknut. The blade
screws
9/16"
Pipe Material
PVC
PVC
PVC
Steel
PE
Steel
PE
PE
Cast Iron, Pit Cast, Ductile Iron, Clay, Concrete
Cast Iron, Pit Cast, Ductile Iron, Clay, Concrete
/
diameter
5
8
rear set
screws
Exhaust
Collar
Motor Clamp screws
3
Publicidad
