SAFETY PRECAUTIONS
•
Read, understand, and practice the precautionary and operating instructions. Know the limitations associated with the
Hydrocollator SS-2, M-2, SS, E-2, E-1, M-4 Heating Units. Observe the cautionary and operational decals installed on the
unit.
•
DO NOT operate this unit in an environment where other devices are being used that intentionally radiates
electromagnetic energy in an unshielded manner. Portable and mobile RF communications equipment can affect Medical
Electrical Equipment.
•
The Hydrocollator Heating Unit generates, uses, and can radiate radio frequency energy and, if not installed and used
in accordance with the instructions, may cause harmful interference to other devices in the vicinity. However, there is
no guarantee that interference will not occur in a particular installation. Harmful interference to other devices can be
determined by turning the Hydrocollator Heating Unit on and off. Try to correct the interference using one or more of
the following: reorient or relocate the receiving device, increase the separation between the equipment, connect the
equipment to an outlet on a different circuit from that which the other device(s) are connected and consult the DJO, LLC
Service Department for help.
•
Do not use accessories other than those supplied with the Hydrocollator Heating Unit or recommended by DJO, LLC. The
safety of other products has not been established, and their use could result in injury to the patient.
•
Never adjust the thermostat too high. The thermostat is extremely sensitive and the slightest adjustment will alter the
temperature several degrees. The recommended operating temperature is 71° to 74° C (160° F to 165° F). The temperature
of the water should be checked with a thermometer after every adjustment, before using the HotPac. Always allow
sufficient time for the water temperature to stabilize.
•
The Hydrocollator Heating Unit should not be installed above a surface that is susceptible to casual water damage.
•
Always keep the water level over the top of the HotPacs to avoid burning or scorching of the packs.
•
Never allow the HotPacs to dry after use.
•
Check water level daily as it has a natural loss due to evaporation.
•
Clean the tank periodically as described in the maintenance portion of this manual.
•
Check unit periodically for signs of leaking and contact service if leaks are noted.
•
Always replace Hydrocollator HotPacs as soon as they show signs of wear.
•
If the unit is to be left unattended for a period of time, unplug the unit, remove the packs, empty the water, and clean the
tank.
•
Do not move the Hydrocollator while filled with heated water. Tipping over could result in burns to the user or others.
•
Always unplug the Hydrocollator from the power source before attempting to empty water from unit.
•
Always use factory authorized replacement parts.
•
Always destroy and replace HotPacs which are exposed to contamination: hazardous or cleaning materials, bodily fluids,
mold, etc.
•
This unit should be operated, transported and stored in temperatures between -40° C to +70° C (-40° F to +158° F) and no
requirements for atmospheric pressure, with relative humidity ranging 10% to 100%.
•
Treatment time should not exceed 30 minutes.
•
DO NOT retrieve HotPacs from tank or replace HotPacs in tank with unprotected hand.
•
Avoid direct contact with mounting rack in tank.
•
Always wrap HotPac with towel or terry cover before handling or applying to patient.
•
Constantly monitor HotPac application to ensure that the skin is not becoming too hot.
•
Damage to skin can occur from exposure to extreme heat or cold. Note instructions for proper use.
•
DO NOT apply over insensitive skin or in the presence of poor circulation.
•
Never lay or sit on top of the HotPac.
•
DO NOT use HotPac directly over cuts, abrasions or wounds.
•
Consult health care professional before using HotPacs on non-communicative individuals.
•
Exercise extreme caution when using HotPacs on non-communicative individuals.
CAUTION
3
Hydrocollator ® Heating Units