Pre-Operation Check; Set-Up Procedures; Operating Instructions; General Washing Techniques - Landa ZG3-2000 Serie Manual Del Usuario

ZG SERIES PRESSURE WASHER
CAUTION: Hot discharge fluid. Do
CAUTION
not touch or direct discharge
stream at persons.
8. Never make adjustments on
machine while in operation.
HOT DISCHARGE FLUID.
DO NOT TOUCH OR
DIRECT DISCHARGE
STREAM AT PERSONS.
WARNING: High pressure spray
WARNING
can cause paint chips or other
particles to become airborne and
fly at high speeds.
9. Eye safety devices and foot pro-
tection must be worn when us-
USE PROTECTIVE
ing this equipment.
CLOTHING WHEN
OPERATING.
WARNING: Keep water spray
WARNING
away from electric wiring or fatal
electric shock may result.
10. Machines with spray gun
should not be operated with the
spray gun in the off position for
extensive periods of time as this
KEEP WATER
SPRAY AWAY FROM
may cause damage to the
ELECTRICAL WIRING.
pump.
11. The best insurance against an accident is precau-
tion and knowledge of the machine.
12. Landa will not be liable for any changes made to our
standard machines, or any components not pur-
chased from Landa.
13. Read engine safety instructions provided.
14. Never run pump dry or leave spray gun closed longer
than 5 minutes.
15. To reduce the risk of injury, close supervision is nec-
essary when a machine is used near children. Do
not allow children to operate the pressure washer.
This machine must be attended during opera-
tion.
16. Inlet water supply must be cold and clean fresh wa-
ter.

PRE-OPERATION CHECK

❑ Pump oil (SAE 30W non-detergent oil, General)
❑ Cold water supply (6 gpm • 5/8" • 20 psi)
❑ Hose, wand, nozzle (nozzle size per serial plate)
❑ Water filter (intact, non restrictive)
❑ Fuel (unleaded 86 or higher octane)
❑ Engine oil (SAE 10W30)

SET-UP PROCEDURES

This machine is intended for outdoor use. Machine
must be stored indoors when not it use.
1. Attach a 5/8" garden hose to inlet connector. Mini-
mum flow should be 5 gpm.
2. Attach high pressure hose to discharge nipple using
quick coupler. Lock coupler securely into place by
pulling back coupler collar and inserting it onto dis-
charge nipple, then pushing collar forward to lock in
place.
3. Attach wand to spray gun. Then connect the two
wand halves using teflon tape on threads to prevent
leakage.
4. Attach swivel connector on discharge hose to spray
gun using teflon tape on threads.
5. Remove oil plug on top of pressure washer pump
and replace with dipstick supplied.
6. Check oil level on dipstick on top of pump. Oil should
be visible up to indicator mark on dipstick (30W non-
detergent).
7. Fill gasoline tank and check engine oil.

OPERATING INSTRUCTIONS

1. Read engine warning and operating instructions.
2. Turn on water at faucet and pull trigger on spray gun
allowing water to flow until all air has discharged
from system. Check for water leaks; tighten as
needed.
3. Pull wand coupler collar back and insert pressure
nozzle into coupler then secure by pushing collar
forward.
4. Read engine manual, turn on gas valve, choke, turn
switch to start position and pull rope to start. Turn off
choke.
CAUTION: Small engines may kick back. Do not hold
pull rope tightly in hand.
5. With spray nozzle pointed away from you or any-
body else, press trigger on spray gun to obtain pres-
surized spray.
GENERAL
WASHING TECHNIQUES
Hold spray nozzle approximately one foot from the sur-
face being cleaned. Spray at an angle to get under the
material and lift it off.
When washing large objects, use optional detergent in-
jector to apply detergent. Start washing from the bottom
and work up. Better detergent economy and faster re-
sults will be obtained by allowing the detergent to set 5-
10 minutes. After washing, rinse from the top down.
LANDA ZG • REV. 5/02
OPERATOR'S MANUAL
5