Juiceman JM1000M Manual Del Usuario página 10

• The flat blade can be used for:
o Grinding coffee beans (up to 2 cups- approximately 5 oz)
o Grinding nuts (up to 1 cup- approximately 4 oz)
o Making bread and cookie crumbs (up to 2 cups- approximately 5 oz)
ASSEMBLING THE WORKBOWL
1. Place the workbowl on the motor base so the arrow on the workbowl is placed
directly over the unlock symbol on the motor base.
2. Hold handle and rotate workbowl counterclockwise
toward the lock
place (H).
Note: Be sure to lock the workbowl in place before
attaching your desired blade blade and lid.
H
3. Hold selected blade by center shaft and insert onto
center post by pushing straight down (J).
Important: The blades are very sharp. Use caution
when handling and storing.
J
4. Place the lid on the workbowl so that the safety
lock tab is to the right of the safety lock latch (K).
The lock/unlock
and feed chute will be to the back of the appliance.
Important: For your protection this appliance has
an interlock system. The processor will not operate
unless the lid is properly locked in place.
Important: Always press the OFF button to make sure
the appliance is off before securing the lid.
5. Hold feed chute and rotate lid counterclockwise
K
until lid locks into place.
6. Place the cap into the feed chute.
7. The feed chute cap can be removed when adding liquid or additional foods
while the appliance is running.
18
symbol until it clicks firmly into
/ symbols will be facing you
USING THE WORKBOWL
The workbowl is used to coarsely or finely chop, mince, mix and puree foods
to a smooth consistency. Use the workbowl to chop fresh and cooked fruits
and vegetables, cooked meats, fish and poultry; to make pastry; and to make
bread, cookie and cracker crumbs.
1. Follow the directions on above to assemble the workbowl parts of the
appliance.
2. Place food in workbowl.
3. Place lid on workbowl and lock into place by rotating lid counterclockwise.
4. Place feed chute cap in place on top of the feed chute.
Caution: Never use your fingers to direct food through the chute.
5. Select Perfect Prep™, Low or High for desired speed.
Note: Process foods no more than a few seconds at a time. The Perfect Prep™
function produces excellent results and offers greater control.
6. To add food while processor is running remove feed chute cap and insert
food through the feed chute. Replace feed chute cap in the feed chute.
Important: Be sure the blade has completely stopped spinning before
removing the lid from the workbowl.
7. When finished, press the Off button and allow blades to stop revolving
before removing lid. Twist the lid toward the unlock
8. To unlock workbowl turn it clockwise toward the unlock
off motor base.
Note: Remove the workbowl from the appliance before removing the blade to
prevent food from leaking through the center opening of the bowl.
9. Carefully remove the blade by the center post and empty workbowl.
10. Unplug appliance when not in use.
HINTS AND TIPS FOR YOUR WORKBOWL
• The processor works very quickly.
• Watch carefully to avoid over-processing foods.
• The Perfect Prep™ button offers the best control and results.
• For best results, use foods that are about the same size.
• It is recommended that food is cut into ½-inch pieces.
• Do not overload the workbowl.
o Do not process more than 2 cups (500 ml) of food in the workbowl
at one time.
o To chop meat, use no more than 2 cups (approximately 8 oz.) of cooked
meat cut into ½-inch cubes and process using the Perfect Prep™
button in 2 second intervals.
Important: When chopping meat, always make sure it is at room
temperature to ensure optimal performance.
• Never walk away from the appliance while it is on.
• To avoid splattering, use a funnel inserted into the feed chute when adding
ingredients, such as oil, flour and sugar.
symbol to remove.
symbol and lift
19