Milwaukee 2112-20 Guia De Inicio Rapido

IMPORTANT SAFETY INSTRUCTIONS
READ AND UNDERSTAND ALL INSTRUC-
WARNING
TIONS.
Failure to follow all instructions listed below,
may result in electric shock, fire and/or serious personal injury.
SAVE THESE INSTRUCTIONS
1. SAVE THESE INSTRUCTIONS - THIS MANUAL CONTAINS IM-
PORTANT SAFETY AND OPERATING INSTRUCTIONS FOR THE
REDLITHIUM USB BATTERY CAT. NO. 48-11-2130 AND USB RE-
®
CHARGEABLE LIGHT.
2. USE AND CHARGE ONLY REDLITHIUM USB BATTERIES IN THIS USB
®
RECHARGEABLE LIGHT. OTHER TYPES OF BATTERIES MAY CAUSE
PERSONAL INJURY AND DAMAGE.
3. BEFORE USING THE BATTERY AND LIGHT, READ THIS OPERATOR'S
MANUAL AND ALL LABELS ON THE BATTERY AND LIGHT.
4. USE ONLY WITH LISTED/CERTIFIED ITE POWER SUPPLY. Others may
result in a risk of fire, electric shock or personal injury.
5. AVOID DANGEROUS ENVIRONMENTS. Do not charge battery in rain, snow,
damp or wet locations. Do not use battery or charger in the presence of explosive
atmospheres (gaseous fumes, dust or flammable materials) because sparks
may be generated when inserting or removing battery, possibly causing fire.
6. CHARGE IN A WELL VENTILATED AREA. Do not block charger vents.
Keep them clear to allow proper ventilation. Do not allow smoking or open
flames near a charging battery. Vented gases may explode.
7. MAINTAIN CORD. When unplugging charger, pull plug rather than cord
to reduce the risk of damage to the electrical plug and cord. Never carry
charger by its cord. Keep cord from heat, oil and sharp edges. Make sure
cord will not be stepped on, tripped over or subjected to damage or stress.
Do not use charger with damaged cord or plug. Have a damaged charger
replaced immediately.
8. USE ONLY RECOMMENDED ATTACHMENTS. Use of an attachment not
recommended or sold by the battery charger or battery manufacturer may
result in a risk of fire, electric shock or personal injury.
9. TO REDUCE THE RISK OF ELECTRIC SHOCK, always unplug charger
before cleaning or maintenance.
10. DO NOT BURN OR INCINERATE BATTERY PACKS. Battery may
explode, causing personal injury or damage. Toxic fumes and materials
are created when battery are burned.
11. DO NOT CRUSH, DROP, OR DAMAGE battery. Do not use a battery or
charger that has received a sharp blow, been dropped, run over, or dam-
aged in any way (e.g., pierced with a nail, hit with a hammer, stepped on).
12. DO NOT DISASSEMBLE. Incorrect reassembly may result in the risk of
electric shock, fire or exposure to battery chemicals. If it is damaged, take
it to a MILWAUKEE service facility.
13. BATTERY CHEMICALS CAUSE SERIOUS BURNS. Never allow contact
with skin, eyes, or mouth. If a damaged battery leaks battery chemicals,
use rubber or neoprene gloves to dispose of it. If skin is exposed to bat-
tery fluids, wash with soap and water and rinse with vinegar. If eyes are
exposed to battery chemicals, immediately flush with water for 20 minutes
and seek medical attention. Remove and dispose of contaminated clothing.
14. DO NOT SHORT CIRCUIT. A battery pack will short circuit if a metal object
makes a connection between the positive and negative contacts on the
battery pack. Do not place a battery pack near anything that may cause
a short circuit, such as coins, keys or nails in your pocket. Do not allow
fluids to flow into battery pack. Corrosive or conductive fluids, such as
seawater, certain industrial chemicals, and bleach or bleach containing
products, etc., can cause a short circuit. A short circuited battery pack
may cause fire, personal injury, and product damage.
15. STORE in a cool, dry place. Do not store battery where temperatures
may exceed 120°F (50°C) such as in direct sunlight, a vehicle or metal
building during the summer.
16. TO REDUCE THE RISK OF INJURY, CLOSE SUPERVISION IS NECES-
SARY when an appliance is used near children.
17. STORE IDLE LIGHT OUT OF REACH OF CHILDREN. Warm lights can
become hazardous in the hands of children.
18. KNOW YOUR LIGHT. Read this manual carefully to learn your light's
applications and limitations as well as potential hazards associated with
this type of light.
19. MAINTAIN LABELS AND NAMEPLATES. These carry important infor-
mation. If unreadable or missing, contact a MILWAUKEE service facility
for a free replacement.
READ AND SAVE ALL
INSTRUCTIONS FOR
FUTURE REFERENCE.
SPECIFICATIONS
Cat. No. .................................................................................. 2112-20
USB Input Volts ............................................................................ 5 DC
USB Input Amps ................................................................... 0.1 - 2.1 A
Output Volts .................................................................................. 4 DC
Output Amps .................................................................................. 2.1A
Battery Cat. No.................................................................. 48-11-2130
Volts .............................................................................................. 4 DC
Operating Temperature
Battery and Charger .............................. 40°F to 104°F (4°C to 40°C)
Battery and Tool .................................... 0°F to 149°F (-18°C to 65°C)
Power Supply Cat. No. ....................................................... 44-66-1202
SYMBOLOGY
Volts
Direct Current
Amps
BFP
Do not stare into
light
BATTERY
To reduce the risk of fire, personal injury, and prod-
WARNING
uct damage due to a short circuit, never immerse
your tool, battery pack or charger in fluid or allow a fluid to flow
inside them. Corrosive or conductive fluids, such as seawater,
certain industrial chemicals, and bleach or bleach containing
products, etc., can cause a short circuit.
Maintenance and Storage
Do not expose your battery or cordless tools to water or rain, or allow
them to get wet. This could damage the tool and battery. Do not use
oil or solvents to clean or lubricate your battery. The plastic casing will
become brittle and crack, causing a risk of injury.
Store batteries at room temperature away from moisture. Do not store
in damp locations where corrosion of terminals may occur. As with other
battery types, permanent capacity loss can result if the pack is stored for
long periods of time at high temperatures (over 120° F). MILWAUKEE
Li-Ion batteries maintain their charge during storage longer than other
battery types. After about a year of storage, charge the battery as normal.
To reduce the risk of injury or explosion, never burn
WARNING
or incinerate a battery pack even if it is damaged, dead
or completely discharged. When burned, toxic fumes and materials
are created.
Disposing of MILWAUKEE Li-Ion Battery
MILWAUKEE Li-Ion batteries are more environmentally friendly than
some other types of power tool batteries. Always dispose of your battery
according to federal, state and local regulations. Contact a recycling
agency in your area for recycling locations.
Even discharged batteries contain some energy. Before disposing, use
electrical tape to cover the terminals to prevent the battery from shorting,
which could cause a fire or explosion.
RBRC Battery Recycling Seals
The RBRC™ Battery Recycling Seals (see "Symbology") on your bat-
teries indicate that MILWAUKEE has arranged for the recycling of that
battery with the Rechargeable Battery Recycling Corporation (RBRC). At
the end of your battery's useful life, return the battery to a MILWAUKEE
Branch Office/Service Center or the participating retailer nearest you.
For more information, visit the RBRC web site at www.rbrc.org.
USB RECHARGEABLE ROVER™ POCKET FLOOD LIGHT
PROJECTEUR ETANCHE DE POCHE RECHARGEABLE PAR USB ROVER™
REFLECTOR DE BOLSILLO RECARGABLE CON ENTRADA USB ROVER™
USB RECHARGEABLE POCKET
WARNING
may cause personal injury and damage.
1. Slide the battery door back and lift up.
2. Line up the battery with the compartment and fully insert the battery.
3. Close the battery door securely.
1. Plug your USB cable into a power source such as an AC wall adaptor,
computer or car port.
2. Lift the rubber cover to expose the micro USB port. Insert the micro
USB plug into the micro USB port.
3. The indicator light will display the charging status:
Red Flashing: Charging, 0-25% charged
Orange Flashing: Charging, 25-80% charged
Green Flashing: Charging, 80-99% charged
Green Solid: 99-100% Charged
Red/Green Flashing: Damaged or Faulty Battery
If the light indicator flashes red and green, check that the battery is fully
seated into the bay. Remove the battery and reinsert. If the light con-
tinues to flash red and green, the battery may be extremely hot or cold,
or wet. Allow the battery to cool down, warm up, or dry out and then
reinsert. If the problem persists, contact a MILWAUKEE service facility.
WARNING
Press the power button
The fuel gauge will display the battery life:
Red Flashing: 0-10% remaining
Red Solid: 10-25% remaining
Orange Solid: 25-80% remaining
Green Solid: 80-100% remaining
WARNING
performing any maintenance. The charger and battery have no in-
ternal serviceable parts. Never disassemble the battery or charger.
Store your charger in a cool, dry place.
As a general practice, it is best to unplug battery chargers and remove
batteries when not in use. No battery damage will occur, however, if the
charger and battery are left plugged in.
WARNING
liquid to flow inside them.
Clean out dust and debris from charger vents and electrical contacts
by blowing with compressed air. Use only mild soap and a damp cloth
to clean the battery and charger, keeping away from all electrical
contacts. Certain cleaning agents and solvents are harmful to plastics
and other insulated parts. Some of these include gasoline, turpentine,
lacquer thinner, paint thinner, chlorinated cleaning solvents, ammonia
and household detergents containing ammonia. Never use flammable
or combustible solvents around batteries, charger, or tools.
1-800-SAWDUST
Contact Corporate After Sales Service Technical Support with technical,
service/repair, or warranty questions.
Email: metproductsupport@milwaukeetool.com
Become a Heavy Duty Club Member at www.milwaukeetool.com to
receive important notifications regarding your tool purchases.
LIMITED WARRANTY - USA & CANADA
Every MILWAUKEE REDLITHIUM USB battery and charger* is warranted to the original purchaser only to be free
from defects in material and workmanship. Subject to certain exceptions, MILWAUKEE will repair or replace repair
a REDLITHIUM USB battery or charger which, after examination, is determined by MILWAUKEE to be defective in
material or workmanship for a period of two (2) years after the date of purchase unless otherwise noted. Return of the
REDLITHIUM USB battery or charger to a MILWAUKEE factory Service Center location or MILWAUKEE Authorized
Service Station, freight prepaid and insured, is required. For the proper shipping procedure of battery packs, contact
1.800.SAWDUST (1.800.729.3878), or go to www.milwaukeetool.com. A copy of the proof of purchase should be
included with the return product. This warranty does not apply to damage that MILWAUKEE determines to be from
repairs made or attempted by anyone other than MILWAUKEE authorized personnel, misuse, alterations, abuse,
normal wear and tear, lack of maintenance, or accidents.
Normal Wear: This warranty does not cover repair or replacement when normal use has exhausted the life of a part
including, but not limited to charging cables, and wall plugs.
*This warranty does not cover any cordless product sold with the REDLITHIUM USB battery and/or charger. There
are separate and distinct warranties available for these products.
ACCEPTANCE OF THE EXCLUSIVE REPAIR AND REPLACEMENT REMEDIES DESCRIBED HEREIN IS A CONDI-
TION OF THE CONTRACT FOR THE PURCHASE OF EVERY MILWAUKEE PRODUCT. IF YOU DO NOT AGREE
TO THIS CONDITION, YOU SHOULD NOT PURCHASE THE PRODUCT. IN NO EVENT SHALL MILWAUKEE BE
LIABLE FOR ANY INCIDENTAL, SPECIAL, CONSEQUENTIAL OR PUNITIVE DAMAGES, OR FOR ANY COSTS,
ATTORNEY FEES, EXPENSES, LOSSES OR DELAYS ALLEGED TO BE AS A CONSEQUENCE OF ANY DAM-
AGE TO, FAILURE OF, OR DEFECT IN ANY PRODUCT INCLUDING, BUT NOT LIMITED TO, ANY CLAIMS FOR
LOSS OF PROFITS. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR
Read Operator's
CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU. THIS
WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER EXPRESS WARRANTIES, WRITTEN OR ORAL.
Manual
TO THE EXTENT PERMITTED BY LAW, MILWAUKEE DISCLAIMS ANY IMPLIED WARRANTIES, INCLUDING
WITHOUT LIMITATION ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR
USE OR PURPOSE; TO THE EXTENT SUCH DISCLAIMER IS NOT PERMITTED BY LAW, SUCH IMPLIED WAR-
Properly Recycle
RANTIES ARE LIMITED TO THE DURATION OF THE APPLICABLE EXPRESS WARRANTY AS DESCRIBED
ABOVE. SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, SO
Batteries
THE ABOVE LIMITATION MAY NOT APPLY TO YOU, THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS,
AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE.
This warranty applies to product sold in the U.S.A. and Canada only.
Please consult the Find a Service Center Search in the Parts & Service section of MILWAUKEE's website www.
Backfeed Protected
milwaukeetool.com or call 1.800.SAWDUST (1.800.729.3878) to locate your nearest MILWAUKEE factory Service
Center location.
LIMITED WARRANTY - USA & CANADA
California Energy
Commission
Every MILWAUKEE Personal Lighting Product* (see exceptions below) is warranted to the original purchaser only to
be free from defects in material and workmanship. Subject to certain exceptions, MILWAUKEE will repair or replace
any part on a personal lighting product which, after examination, is determined by MILWAUKEE to be defective in
material or workmanship for the lifetime of the personal lighting product. Return of the personal lighting product
to a MILWAUKEE factory Service Center location or MILWAUKEE Authorized Service Station, freight prepaid and
insured, is required. A copy of the proof of purchase should be included with the return product. This warranty
does not apply to damage that MILWAUKEE determines to be from repairs made or attempted by anyone other
than MILWAUKEE authorized personnel, misuse, alterations, abuse, normal wear and tear, lack of maintenance,
accidents, or caused by alkaline batteries.
Normal Wear: This warranty does not cover repair or replacement when normal use has exhausted the life of a
part including, but not limited to clips, straps, charging cables, wall plugs, and rubber gaskets. This warranty does
cover the LED in the personal lighting products, subject to the limitations herein.
*This warranty does not cover Cordless Battery Packs or Chargers. There are separate and distinct warranties
available for these products.
ACCEPTANCE OF THE EXCLUSIVE REPAIR AND REPLACEMENT REMEDIES DESCRIBED HEREIN IS A CONDI-
TION OF THE CONTRACT FOR THE PURCHASE OF EVERY MILWAUKEE PRODUCT. IF YOU DO NOT AGREE
TO THIS CONDITION, YOU SHOULD NOT PURCHASE THE PRODUCT. IN NO EVENT SHALL MILWAUKEE BE
LIABLE FOR ANY INCIDENTAL, SPECIAL, CONSEQUENTIAL OR PUNITIVE DAMAGES, OR FOR ANY COSTS,
ATTORNEY FEES, EXPENSES, LOSSES OR DELAYS ALLEGED TO BE AS A CONSEQUENCE OF ANY DAM-
AGE TO, FAILURE OF, OR DEFECT IN ANY PRODUCT INCLUDING, BUT NOT LIMITED TO, ANY CLAIMS FOR
LOSS OF PROFITS. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR
CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU. THIS
WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER EXPRESS WARRANTIES, WRITTEN OR ORAL.
TO THE EXTENT PERMITTED BY LAW, MILWAUKEE DISCLAIMS ANY IMPLIED WARRANTIES, INCLUDING
WITHOUT LIMITATION ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR
USE OR PURPOSE; TO THE EXTENT SUCH DISCLAIMER IS NOT PERMITTED BY LAW, SUCH IMPLIED WAR-
RANTIES ARE LIMITED TO THE DURATION OF THE APPLICABLE EXPRESS WARRANTY AS DESCRIBED
ABOVE. SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, SO
THE ABOVE LIMITATION MAY NOT APPLY TO YOU, THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS,
AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE.
This warranty applies to product sold in the U.S.A. and Canada only.
Please consult the Find a Service Center Search in the Parts & Service section of MILWAUKEE's website www.
milwaukeetool.com or call 1.800.SAWDUST (1.800.729.3878) to locate your nearest MILWAUKEE factory Service
Center location.
INSTRUCTIONS DE SÉCURITÉ
AVERTISSEMENT
instructions ci-après peut entraîner des chocs électriques, des in-
cendies et/ou des blessures graves.
CONSERVER CES INSTRUCTIONS
1. GARDEZ CES INSTRUCTIONS – CE MANUEL CONTIENT DES IN-
STRUCTIONS D'OPÉRATION ET SÉCURITÉ IMPORTANTES À PROPOS
DE LA PILE RECHARGEABLE PAR USB REDLITHIUM
AINSI QUE LA LAMPE RECHARGEABLE PAR USB.
2. N'UTILISEZ NI NE CHARGEZ QUE LES PILES RECHARGEABLES PAR
USB REDLITHIUM
PAR USB. D'AUTRES TYPES DE PILES POURRONT ENTRAÎNER DES
BLESSURES ET DOMMAGES.
FLOOD LIGHT
Use and charge only REDLITHIUM USB batteries in
®
this USB rechargeable light. Other types of batteries
Inserting the Battery
Charging the Battery
Operation
To reduce the risk of injury, do not look directly into
the light when the light is on.
firmly to cycle through High, Low, and Off.
To reduce the risk of injury, always unplug the charg-
er and remove the battery from the charger before
Maintenance and Storage
To reduce the risk of injury and damage, never im-
merse your battery or charger in liquid or allow a
Cleaning
SERVICE - UNITED STATES
(1.800.729.3878)
Monday-Friday, 7:00 AM - 6:30 PM CST
www.milwaukeetool.com
or visit
SERVICE - CANADA
Milwaukee Tool (Canada) Ltd
1.800.268.4015
Monday-Friday, 7:00 AM - 4:30 PM CST
or visit www.milwaukeetool.ca
IMPORTANTES
LIRE ET COMPRENDRE TOUTES LES
INSTRUCTIONS.
Le non-respect des
N.º 48-11-2130
®
DANS CETTE LAMPE DE POCHE RECHARGEABLE
®
3. AVANT D'UTILISER LA PILE ET LA LAMPE DE POCHE, LISEZ CE MA-
NUEL DE L'OPERATEUR AINSI QUE TOUTES LES ÉTIQUETTES QUI
SE TROUVERONT SUR LA LAMPE DE POCHE ET LA PILE.
4. N'UTILISEZ QUE D'ALIMENTATION ELECTRIQUE LISTEE/CERTIFIE
TI. D'autres pourront entraîner des risques d'incendie, chocs électriques
ou blessures.
5. ÉVITEZ DES MILIEUX DANGEREUX. Ne chargez pas la pile dans des
milieux ayant de la pluie, neige, humidité ni d'environnements mouillés.
N'utilisez pas la pile ni le chargeur dans des atmosphères explosives
(ayant des vapeurs gazeux, poudre ou matériel inflammable) parce que
des étincelles pourront être créées lorsque la pile est insérée ou retirée,
pouvant bien provoquer des incendies.
6. CHARGEZ-LA DANS UN ESPACE BIEN AÉRÉ. Ne bloquez pas les
bouches du chargeur. Préservez-las propres pour assurer une bonne
aération. Ne laissez pas de fumes ni flames décontrôlées près d'une pile
du chargeur. Les gaz aérés pourront exploser.
7. PRÉSERVEZ LE FIL. Lorsque le chargeur est débranché, tirez de la fiche
en lieu du fil afin de réduire les risques de dommages sur tous les deux. Ne
portez jamais le chargeur par son fil. Ne laissez pas que le fil soit exposé à
chaleur, huile ni aux bords tranchants. Assurez-vous de laisser le fils dans
un endroit où il ne pourra pas être marché, trébuché ou endommagé ni sous
contrainte. N'utilisez pas le chargeur avec une fiche ou un fil endommagés.
Demandez que le chargeur endommagé soit remplacé immédiatement.
8. N'UTILISEZ QUE LES ACCESSOIRES RECOMMANDÉS. L'utilisation
d'un accessoire que ne soit pas recommandé ou vendu par le fabriquant
de la pile ou le chargeur pourra entraîner des risques d'incendies, chocs
électriques ou blessures.
9. AFIN DE RÉDUIRE LE RISQUE DE CHOC ÉLECTRIQUE, débranchez
toujours le chargeur avant de le nettoyer ou l'entretenir.
10. NE BRÛLEZ PAS NI N'INCINÉREZ PAS LES BLOC-PILES. La pile
pourra exploser, en entraînant des dommages ou blessures. Des vapeurs
ou matériaux toxiques sont créés lorsque la pile est brûlée.
11. N'ÉCRASEZ PAS la pile, NE LA LAISSEZ PAS TOMBER NI NE
L'ENDOMMAGEZ PAS. N'utilisez pas une pile ni un chargeur qui ait reçoit
un coup sec, été marché, écrasé ou endommagés de n'importe quelle
forme (par exemple, percé par un clou, frappé par un marteau, marché).
12. NE LE DÉSASSEMBLEZ PAS. Le démantèlement incorrect peut entraîner
un risque de chocs électriques, incendie ou exposition à produits chimiques.
Si l'outil est endommagé, amenez-le au centre de service MILWAUKEE.
13. LES PRODUITS CHIMIQUES ENTRAÎNENT DES BRÛLURES GRAVES.
Ne permettez pas qu'ils entrent en contact avec la peau, les yeux ni la
bouche. Si de la pile endommagée des produits chimiques se coulent,
utilisez des gants en caoutchouc ou néoprène pour se débarrasser d'elle.
Si la peau est exposée à des fluides de la pile, lavez-la avec du savon
et de l'eau et rincez-la avec du vinaigre. Si les yeux sont exposés aux
produits chimiques de la pile, lavez-les avec pleine de l'eau pendant 20
minutes et consultez un médecin. Retirez les vêtements contaminés et
se débarrassez d'eux.
14. ATTENTION AUX COURTS-CIRCUITS! Un bloc-piles court-circuite si
un objet métallique établit une connexion entre les contacts positifs et
négatifs sur le bloc-piles. Ne placez pas un bloc-piles près de tout ce qui
peut causer un court-circuit, comme des pièces de monnaie, des clés ou
des clous dans votre poche. Ne pas laisser les fluides s'écouler dans le
bloc-piles. Les fluides corrosifs ou conducteurs, tels que l'eau de mer,
certains produits chimiques industriels, les produits de blanchiment ou
de blanchiment, etc., peuvent provoquer un court-circuit. Un bloc-batterie
court-circuité peut provoquer des incendies, des blessures corporelles et
des dommages au produit.
15. L'ENTREPOSEZ dans un endroit sec et bien aéré. Ne mettez la pile où
les températures pourront surpasser les 50 ºC (120 ºF), tels que la lumière
du soleil, un véhicule ou un bâtiment en acier en été.
16. AFIN DE RÉDUIRE LE RISQUE DE BLESSURES, SUPERVISION
ÉTROITE EST REQUISE quand un appareil est utilisé près d'enfants.
17. TENEZ L'INDICATEUR DE REPOS HORS DE LA PORTÉE DES ENFANTS.
Des lumières chaudes peuvent être dangereuses dans la portée des enfants.
18. CONNAISSEZ VOTRE LAMPE. Lisez attentivement ce manuel de
l'opérateur pour savoir à propos des applications et limitations de la lampe
ainsi que les dangers possibles liés à ce type de lampe.
19. PRÉSERVEZ LES ÉTIQUETTES ET PLAQUES NOMINATIVES. Elles
montrent d'information importante. Si elle est illisible ou manquante,
contactez un centre de service MILWAUKEE afin de recevoir un outil
substitutif gratuit.
LIRE ET CONSERVER
TOUTES LES INSTRUCTIONS
POUR RÉFÉRENCE FUTURE.
SPÉCIFICATIONS
No de Cat.. ............................................................................. 2112-20
Voltage d'entrée par USB ............................................................ 5 CD
Ampérage d'entrée par USB ............................................... 0,1 - 2,1 A
Voltage de sorti ............................................................................ 4 CD
Ampérage de sorti ......................................................................... 2,1A
Cat. de la pile .................................................................... 48-11-2130
Voltage.......................................................................................... 4 CD
Température opérative
Pile et chargeur ................................... 4°C to 40°C (40°F to 104°F)
Pile et outil ............................................ -18°C to 65°C (0°F to 149°F)
No de Cat. de la prise d'alimentation ............................... 44-66-1202
PICTOGRAPHIE
Lisez le manuel
Volts
de l'operateur
Courant direct
Recyclage correct
des batteries
Ampères
BFP
Rétro-alimentation protégée
Ne pas regarder
Commission à l'Énergie de
dans la lumière
la Californie
BLOC-PILES
Pour réduire le risque d'incendie, de blessures
AVERTISSEMENT
corporelles et de dommages causés par un
court-circuit, ne jamais immerger l'outil, le bloc-piles ou le chargeur
dans un liquide ou laisser couler un fluide à l'intérieur de celui-ci. Les
fluides corrosifs ou conducteurs, tels que l'eau de mer, certains pro-
duits chimiques industriels, les produits de blanchiment ou de blanchi-
ment, etc., peuvent provoquer un court-circuit.
Entretien et entreposage
Ne pas exposer votre bloc-piles ni vos outils sans fil à l'eau ou la pluie,
ou les laisser prendre l'humidité. Cela pourrait endommager l'outil et le
bloc-piles. Ne pas utiliser d'huile ou solvants pour nettoyer ou lubrifier
votre bloc-piles. Le boîtier du bloc-piles risque de devenir cassant ou
de se fendiller, causant un risque de blessure.
Entreposer les blocs-piles à température ambiante à l'abri de l'humidité.
Ne pas les entreposer dans un endroit humide où la corrosion des
bornes peut survenir. Comme pour d'autres types de batteries, une
perte permanente de capacité peut survenir si le bloc-piles est entre-
posé pendant longtemps à haute température (48°C/120°F). Les piles
Li-ion MILWAUKEE maintiennent leur charge pendant plus longtemps
que les autres types de piles. Après un an d'entreposage, rechargez le
bloc-piles comme d'habitude.
Pour réduire le risque d'explosion, ne jamais
AVERTISSEMENT
brûler un bloc-piles, même s'il est endom-
magé ou complètement déchargé. Lorsqu'il est brûlé, des matières
et vapeurs toxiques sont produites.
Mise au rebut du bloc-piles Li-ion MILWAUKEE
Les blocs-piles Li-ion MILWAUKEE sont plus écologiques que d'autres
types de piles pour outils portables. Mettre au rebut votre bloc-piles
conformément aux réglementations locales, nationales et fédérales.
Contacter une agence de recyclage dans votre région pour les lieux
de recyclage.
Même déchargés, les blocs-piles contiennent un peu d'énergie. Avant
la mise au rebut, utiliser du ruban isolant pour recouvrir les contacts
pour empêcher la mise en court-circuit, laquelle pourrait causer un
incendie ou une explosion.