Sammic SL-650C Manual De Instrucciones página 8

Tabla de contenido

Publicidad

Idiomas disponibles
  • MX

Idiomas disponibles

  • MEXICANO, página 1
reached. This prevents rinsing with cold water.
In order to enable this feature, select the
appropriate digit from the following table:
B
B
REAK
REAK
M
D
ODEL
RAIN
T
T
ANK
ANK
PUMP
DISCHARGE
INTAKE
15
YES
NO
YES
16
YES
NO
YES
17
YES
NO
YES
18
YES
NO
YES
Configuration Selection:
The machine configuration number appears on
the display for 2 seconds once the main switch
is turned on. In order to select another
configuration number, proceed as follows:
1.Power the machine down.
2.Move the two microswitches (Fig B-3) to the
ON position.
3.Power the machine up.
4.Press key (Fig B-5): the configuration number
is displayed.
5.Press "Start" (Fig A-5) to increment the
configuration number.
6.Press "Drain" (Fig A-7) to decrement the
configuration number.
7.After selecting the number required, press the
Cycle Selection key (Fig A-4) to confirm.
8.Power the machine down.
9.Move the two microswitches (Fig B-3) to the
OFF position.
10.Power the machine up: the selected
configuration number appears on the display.
OPERATION
S
-
TART
UP
1.Open the 3/4" stopcock to allow water to enter
the machine.
2.Turn on the magnetothermal switch that
protects the installation.
3.Check that the filter of the motor-driven pump
(M), the upper filters (N) and the drain plug
are in place.
4.Turn the main switch (Fig. A-1) to the ON
position for the automatic filling of the wash
tank and the connection of the heater
elements.
5. The light indicator (Fig.A, C) turns on when
the washing temperatur 55/60ºC has been
reached. If the washer has no automatic
8
ENGLISH
detergent dispenser, introduce the detergent
into the tank: 1/2 coffee cup at the beginning
of the first cycle and a same amount every 10
cycles approximately.
6. Start Cycle:
T
HERMAL
-Place the objects to be washed in
ºF
ºC
L
MODEL
OCK OF
C
YCLE
a basket (rack).
NO
YES
NO
SL-650C
-Close the door.
-Select the washing programme
NO
YES
YES
SL-650C
by pressing key A-4, according to
the level of soiling. The relevant
YES
NO
NO
SL-650C
red LED will turn on.
YES
NO
YES
SL-650C
-Press the Start Cycle key (A-5).
The washing phase indicator light
(A-g) turns on. The machine completes the
entire washing cycle. If you press the Start
Cycle key (A-5) again during the washing
phase, the programme immediately shifts to the
rinsing process. Pressing the said key during
the rinsing phase causes the machine to stop.
7.When the complete cycle has finished, the
two indicators (A-g) and (A-h) flash.
8.Models with a drain pump: With the door
open, press key (A-7) to start the drain pump
for a given period of time, which is long
enough to empty the tub. At the end of this
time, the pump stops. Press key (A-7) to
alternately start and stop the pump. With
overflow (C-2) in place, any residual water will
be removed from the tub.
D
ETERGENT DISPENSER
The dispenser delivers about 0.7ml/s of
detergent (maximum). At the first filling of the
tank, feeding of detergent is roughly 119ml in
170s, resulting in a maximum concentration of
3ml/l. At each cycle, the dispenser delivers
10ml of detergent. It is possible to reduce or
increase the injected quantity by turning the
adjusting screw on the dispenser.
Rinsing aid dispenser
The dishwasher features a peristaltic metering
pump that delivers approximately 0.17ml/s of
rinsing aid (maximum). It is possible to reduce
or increase the injected quantity by turning the
adjusting screw on the dispenser.
In order to determine whether the amount of
rinsing aid is adequate, look at the glasses
against the light. If there are water droplets on
the glass, the amount of rinsing aid is
insufficient; if streaks develop, the quantity of
rinsing aid is too much.
M
D
ACHINE
RAINING
·Open the door and take out the drain plug,
leaving the filters in place.
·Press the drain key (A-7) as specified on the
control panel, with the door open. The drain
pump operates during the programmed time at
the end of which it stops automatically. By
pressing the key, you can successively start
and stop the pump.
·Put the overflow drain plug and filters in place
again.
·Turn the main switch off and close the door.
B
D
OILER
RAINING
When it is necessary to drain the boiler due to a
failure, the break tank will empty too. Proceed
as follows:
1.Drain the wash tank.
2.Close the water inlet.
3.Remove the tube coming from the rinsing aid
pump from the inlet connector to the boiler and
place a container under the boiler. All water
flows out of the boiler and the break tank, as
both communicate, by gravity.
T
ANK CLEANING
The tank should be cleaned after every washing
process, at the end of the day, proceeding as
follows: Fig.C
· Remove the top filters and the tub filter (H) and
clean them carefully.
· Remove the bayonnet safety filter from the
wash pump (L) by twisting it counterclockwise.
· Also, remove the screwed-on filter (J) from the
drain pump and clean it. As Figure 2 shows,
give the filter (J) a quarter of a turn to unscrew
it. After cleaning the filter, replace it.
·At the end of the day, it is advisable to drain the
dishwasher, fill it with water and have a wash
cycle done on no load, without any racks, in
order to clean the interior of the machine.
·Finally, clean the bottom, walls and interior of
the tank.
·Spray arms must be cleaned periodically. If
rinsing is deficient, the cause may be an
obstruction of the jets. In this event, dismount
the arms and clean the jets.
·The outside of the machine MUST NOT BE

Publicidad

Tabla de contenido
loading

Tabla de contenido