Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
Timings
In this section it is possible to program the timings of all the
actuations of the system. By pressing
gramming procedure, whilst pressing
previous menu. Parameters that can be programmed are:
- Activation time for S+S-: activation time for the "open door"
circuit (terminals S+ ed S-).
- Activation time for auxiliary relè: activation time for the
auxiliary relay (terminals C, NC ed NO).
With arrows
or
select the parameter to be programmed
and confirm with the
vious menu.
Activation time for S+S-
By pressing
you enter the programming mode, while
key backwards you to the previous menu. Entering the menu,
the first line of LCD shows "Enter time", while on the bottom
of the second line the activation time currently stored is report-
ed (1 sec. from factory). With
enter the new one (max. 9 sec.) and then confirm by pressing
, display will show briefly "saved" after that the system re-
turns to the previous menu.
Attivation time for the auxiliary relay
By pressing
you enter the programming mode, while
key backwards you to the previous menu. Entering the menu,
the first line of LCD shows "Enter time", while on the bottom
of the second line the activation time currently stored is report-
ed (1 sec. from factory). With
then, enter the new one (max. 98 sec.; entering the value 99
the auxiliary relay will act as bi-stable device) and then confirm
, display will briefly show "saved" after which
by pressing
the system returns to the previous menu.
Administrator Password
From the factory the administrator password is 0039, but it can
be changed with a new one chosen by the installer or the instal-
lation manager. Pressing
and at the end of the second line of the LCD the current admin-
istrator password is reported (0039 from factory), erase the old
one using the
key and then enter the new password, press
to confirm, display will briefly show "saved" after which the
system returns to the previous menu.
Attention: write down and keep the administrator pass-
word in a safety place, without the administrator password it is
impossibile to program the device.
Miscellaneous
In this section of the menu it is possible to program the general
parameters of the system which are:
-
key to send a call
- Conversation time
- External camera (TLC)
- Welcome message
- LCD contrast
- FW version
With
or
arrows select the parameter to be set and confirm
with
.
key backwards you to the previous menu.
key to send a call
It is possible to chose the operating mode for sending a call
which can be:
- manual: after dialing the user address, its alias or after se-
lecting the user name from the directory, it is necessary to
press
to send the call;
- automatic: call is automatically sent 3 sec. from when you
have dialed the user address, its alias or you have selected
the user name from the directory, therefore it is not neces-
sary to press
to send a call.
you enter the pro-
key you return to the
key.
key backwards you to the pre-
erase the old value and then,
key erase the old value and
you enter the programming mode
By pressing the
key you enter the programming mode "
key to send a call" and the first line of LCD shows:
-
key to send call? With arrows
<NO> and then press
and returns to the previous menu.
Conversation time
This function extends the conversation time from 90 sec. (fac-
tory value) to 4 min. Pressing
mode "Conversation time 4 min.", while
you to the previous menu. Entering the programming mode, the
first line of LCD shows:
- Conv. time 4 min? With arrows
<NO> and then press
versation time will be extended up to 4 min; it is always pos-
sible to close the conversation at any time by pressing
the door station or hanging-up the handset on the videoint-
ercom. Choosing <NO> the conversation time remains set to
90 sec., but it is always possible to double the conversation
time pressing, on the door station keypad, the
a tone will warn you that the conversation time is going to
expire.
External camera
Enabling this function the door station will manage an exter-
nal additional camera besides the one present on the device.
When a video door phone sends the "monitoring" commands,
the door station switches from the two cameras and on the vid-
eo door phone you get alternatively the two related images. By
pressing
you enter the programming mode "External cam-
era" and the first line of LCD shows:
- External TLC? With arrows
and then press
to confirm; the system stores your selec-
tion and returns to the previous menu.
Welcome message
During standard operations, on the LCD of the door station a
welcome message, reporting short info on how to call a user,
is displayed. It is composed of two pages (2 lines for 20 char-
acters each) that can be customized and which would alternate
each 6 seconds. Pressing
"Message programming", whilst
previous menu. The programming section is composed of two
parts:
- Message 1
- Message 2
With arrows
or
select which of the two massages you
wish to modify, then press
display on which it is possible to write a message using the key-
pad of the door station as described in the paragraph "How to
use the keypad". After entering the new message, press
store. Proceed in the same way, if required, to enter the second
message.
Attention: it is sufficient to program only one of the two
messages so that the system considers it as a welcome mes-
sage, in this case the LCD will remain fix on it.
LCD Contrast
It is possible to adjust the LCD contrast; pressing
the "LCD contrast" menu and the first line of LCD shows:
- LCD contrast: with
the contrast value, as indicated on the display, and press
to confirm, system stores the entered value and returns to
the previous menu.
Firmware version
Pressing
LCD will show the firmware version currently pro-
grammed in the device. Pressing the
the previous menu.
or
select <YES> or
; the system stores your selection
you enter the programming
key backwards
or
select <YES> or
to confirm. Choosing <YES> con-
or
select <YES> or <NO>
you enter the programming mode
key backwards you to the
to confirm. LCD shows a blanked
or
arrows, increase or decrease
the system returns to
Mi 2513/2
on
key when
to
you enter
- 18 -
Publicidad
Tabla de contenido
