Display Light Bulb Replacement; Accessories; Led Temperature Control; 10 Cm (4") Adjustable Legs - Hatco GLO-RAY GRSDH Serie Manual Del Usuario

MAINTENANCE

DISPLAY LIGHT BULB REPLACEMENT

The display light is an incandescent light bulb which illuminates
the warming area. The bulb has a special coating to guard against
injury and food contamination in the event of breakage.
1. To replace a light bulb, disconnect the power supply and wait
until the unit has cooled.
2. Light bulbs have a threaded base. Unscrew the light bulb from
the unit and replace it with a new specially-coated incandescent
light bulb.
NOTE: Hatco shatter-resistant light bulbs meet N.S.F. standards
for food holding and display areas. For 120, 120/208
and 120/240 volt applications, use Hatco part #02.30.043.00. For
220 or 240 volt applications, use Hatco part #02.30.058.00
CAUTION
Only light bulbs which meet or exceed N.S.F. standards,
specifically designed for food holding areas must be used.
Breakage of light bulbs not specially coated could result
in personal injury and/or food contamination.

ACCESSORIES

LED TEMPERATURE CONTROL

Units may be equipped with an LED temperature control device
which regulates the base temperature and also indicates the current
base temperature.
NOTE: This option is factory installed only, not available
for retrofit.
NOTE: Units with the LED temperature control do not have
an additional separate base thermostat. All temperature regulation
is performed by the controller.
NOTE: Units with LED temperature controls manufactured for
use outside the United States use devices that indicate temperature
in Celsius (°C).
The programming instructions are as follows:
1. To set the temperature, turn the red Mode Switch
counterclockwise to the SP-1 position indicated
on the controller. See 11 .
2. Adjust the Setpoint Screw to the desired temperature, then turn
the red Mode Switch to the TEMP position. The surface
temperature range is room temperature to 93°C (200°F).

10 cm (4") ADJUSTABLE LEGS

CAUTION
The National Sanitation Foundation (NSF) requires units over
91 cm (36") in length or weighing more than 36 kg (80 lbs.)
to be either sealed or raised on the installation surface. If this
unit cannot be sealed at the point of use, 10 cm (4") legs are
included to allow for proper cleaning access below unit.
Form No. GRSDCEM-1002
If service is required on this unit, contact your Authorized
Hatco Service Agent, or contact the Hatco Service Department
at 800-558-0607 or 414-671-6350; fax 800-690-2966
or International fax 414-671-3976.
This product has no "user" serviceable parts. To avoid damage
to the unit or injury to personnel, use only Authorized Hatco
Service Agents and Genuine Hatco Parts when service
is required.
Genuine Hatco Replacement Parts are specified to operate
safely in the environments in which they are used. Some
aftermarket or generic replacement parts do not have the
characteristics that will allow them to operate safely in Hatco
equipment. It is essential to use Hatco Replacement Parts when
repairing Hatco equipment. Failure to use Hatco Replacement
Parts may subject operators of the equipment to hazardous
electrical voltage, resulting in electrical shock or burn.
Carefully lay unit on its side. Install legs to bottom of unit as shown
in 13 . Hand tighten legs until snug. Do not overtighten. Return
unit to the upright position.
Do not lay unit on the side with the control panel or damage
to unit could occur.
NOTE: Legs are adjustable for leveling the unit. Use a 16 mm
(5/8") open-end wrench to make leveling adjustments once the unit
is placed in final position.

STAINLESS STEEL SIDE PANELS

Optional stainless steel end panels can be ordered in place
of the glass side panels.

DISPLAY SIGN HOLDER

A display sign holder (sign not included) is available for installation
on the top or intermediate shelf. Remove screws from unit
and install sign holder using same screws see 14 .

BACKLIT SIGN HOLDER

120V Slant Models 76 - 132 cm (30" - 52")
Length Only
A backlit sign holder (sign not included) is available for installation
on the front top shelf.

DESIGNER COLORS

Choose an optional Designer color in place of the stainless steel
exterior finish to match décor.
11
WARNING
WARNING
WARNING
WARNING